2ED100E12-F_EVAL Infineon Technologies, 2ED100E12-F_EVAL Datasheet
2ED100E12-F_EVAL
Related parts for 2ED100E12-F_EVAL
2ED100E12-F_EVAL Summary of contents
Page 1
...
Page 2
... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system ...
Page 3
AN2006-04 2006-05 Revision History: Previous Version: none Author: Piotr Luniewski IFAG AIM PMD ID AE Application Note Driver for EconoDUAL 3 AN2006-04 TM V1.0 V1.0, 2006-05 ...
Page 4
Table of Contents 1 Introduction ..............................................................................................................................5 2 Datasheet..................................................................................................................................6 2.1 Main features .............................................................................................................................6 2.2 Key data.....................................................................................................................................7 2.3 Pin assignment ..........................................................................................................................8 2.4 Mechanical dimensions and mounting instructions......................................................................9 3 Application Note.....................................................................................................................10 3.1 Power Supply...........................................................................................................................10 3.2 Input logic – /PWM signals .......................................................................................................10 3.3 Maximum ...
Page 5
... The design of the 2ED100E12-F was performed with respect of the environmental conditions described as design target in the datasheet part. Also the requirements for leadfree reflow soldering have been considered when components were selected ...
Page 6
... Datasheet 2.1 Main features The 2ED100E12 Evaluation Driver Board offers the following features: • Dual channel IGBT driver • Electrically and mechanically suitable for 600V and 1200V EconoDUAL • Integrated and protected against short circuit DC/DC power supply, • Integrated protection against DC/DC power supply short circuit • ...
Page 7
Key data All values given in the table bellow are typical values, measured at Ta=25°C Table 1 Key data and characteristic values Parameter – primary DC/DC voltage supply V DC – /PWM signals for Top and Bottom IGBT (active ...
Page 8
... Fault detection output /FAULT X11, X13, X15, GND Primary ground for DC/DC converter supply voltage X19 Primary ground for input/output signals (/PWMT, /PWMB, TEMP, /FAULT) GND Figure 2 The 2ED100E12-F Evaluation Driver Board pin assignment Application Note Driver for EconoDUAL 8 AN2006-04 TM Datasheet V1.0, 2006-05 ...
Page 9
... Mechanical dimensions and mounting instructions The 2ED100E12-F should be fastened by self taping screw and soldered to the auxiliary connectors on the TM top of the EconoDUAL IGBT module. Detailed information available in application note (AN2006-05). Figure 3 Dimensions of the 2ED100E12-F Clearance distance and creepage between Primary/Secondary is not less than 8mm ...
Page 10
... Additionally, the power supply is protected against gate – emitter short circuit of the IGBTs. In case a DC/DC overcurrent is detected, the output voltage drops down, the IGBT is protected by Under Voltage Detection function and the fault is reported to the isolated 2ED100E12-F side. 3.2 Input logic – ...
Page 11
... Under these conditions the board can dissipate approximately 0,6W. At room temperature the 2ED100E12-F can drive the IGBTs safely with the switching frequency limited by the available power of the DC/DC (1.5W). ...
Page 12
... TD350. Thanks to this operation mode, the collector-emitter overvoltage, which is a result of the stray inductance and the collector current slope, is limited the second level of the turn-off voltage. If the stray inductance is not higher than 30µH the 2ED100E12-F can switch-off the IGBT safely σ ...
Page 13
Fault output When short circuit occurs, the voltage V switched-off. The fault is reported to the isolated side of the driver as long as the active level of PWM signal is applied (see Figure 8 absolutely necessary ...
Page 14
... To meet the individual customer requirement and make the Evaluation Driver Board simple for development or modification, all necessary technical data like schematic, layout and components are included in this chapter. Application Note Driver for EconoDUAL Schematic, Layout and Bill of Material TM modules, the 2ED100E12-F offers IGBT base plate 14 AN2006-04 TM V1.0, 2006-05 ...
Page 15
Schematic Figure 10 IGBT driver – Top transistor Figure 11 IGBT driver – Bottom transistor Application Note Driver for EconoDUAL Schematic, Layout and Bill of Material 15 AN2006-04 TM V1.0, 2006-05 ...
Page 16
Figure 12 IGBT driver – Module connectors Figure 13 IGBT driver – Fault output Figure 14 IGBT driver – Temperature measurement Application Note Driver for EconoDUAL Schematic, Layout and Bill of Material 16 AN2006-04 TM V1.0, 2006-05 ...
Page 17
Figure 15 IGBT driver – DC/DC converter Figure 16 IGBT driver – External connections Application Note Driver for EconoDUAL Schematic, Layout and Bill of Material 17 AN2006-04 TM V1.0, 2006-05 ...
Page 18
Layout Figure 17 IGBT driver – Layer 1 (Top) Figure 18 IGBT driver – Layer 2 Application Note Driver for EconoDUAL Schematic, Layout and Bill of Material 18 AN2006-04 TM V1.0, 2006-05 ...
Page 19
Figure 19 IGBT driver – Layer 3 Figure 20 IGBT driver – Layer 4 (Bottom) Application Note Driver for EconoDUAL Schematic, Layout and Bill of Material 19 AN2006-04 TM V1.0, 2006-05 ...
Page 20
Bill of Material The bill of material includes not only a part list, but also assembly notes. All electronic parts used in the design, except the DC/DC transformer, are lead-free with 260°C soldering profile. The external gate resistors are ...
Page 21
... Semiconductor TD350I SO16 Connector Tyco10POL Transformer T60403- D4615-X054 Cable connector X1, used for 2ED100E12-F input / output signals has part number: 8-215083-0 Application Note Schematic, Layout and Bill of Material C4B, C4T, C6, C12B, no special C17T, C18T, C60, C63 C10B, C10T, C11B, C11T, Murata C13B, C13T, C14B, C14T, ...
Page 22
Gate resistors list Table 5 External gate resistors R Module R [Ω] EXT FF600R06ME3 3,0 FF150R12ME3 8,2 FF225R12ME3 3,3 FF300R12ME3 2,4 FF450R12ME3 1,6 FF150R12MS4 7,5 FF225R12MS4 4,7 FF300R12MS4 2,7 Application Note are listed bellow (all packages are 2010) EXT ...
Page 23
... Published by Infineon Technologies AG ...