CY7C1339G-133AXET Cypress Semiconductor Corp, CY7C1339G-133AXET Datasheet - Page 4

• Manufacturer Part Number: CY7C1339G-133AXET
• Description: IC SRAM 4MBIT 133MHZ 100LQFP
• Manufacturer: Cypress Semiconductor Corp

Specifications of CY7C1339G-133AXET

• Format - Memory: RAM
• Memory Type: SRAM - Synchronous
• Memory Size: 4M (128K x 32)
• Speed: 133MHz
• Interface: Parallel
• Voltage - Supply: 3.15 V ~ 3.6 V
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 100-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Document #: 38-05520 Rev. *F
Pin Definitions
Functional Overview
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. All data outputs pass through
output registers controlled by the rising edge of the clock.
Maximum access delay from the clock rise (t
(250-MHz device).
The CY7C1339G supports secondary cache in systems
utilizing either a linear or interleaved burst sequence. The
interleaved burst order supports Pentium and i486™
processors. The linear burst sequence is suited for processors
that utilize a linear burst sequence. The burst order is user
selectable, and is determined by sampling the MODE input.
Accesses can be initiated with either the Processor Address
Strobe (ADSP) or the Controller Address Strobe (ADSC).
Address advancement through the burst sequence is
controlled by the ADV input. A two-bit on-chip wraparound
burst counter captures the first address in a burst sequence
and automatically increments the address for the rest of the
burst access.
Byte Write operations are qualified with the Byte Write Enable
(BWE) and Byte Write Select (BW
Enable (GW) overrides all Byte Write inputs and writes data to
ADV
ADSP
ADSC
ZZ
DQs
V
V
V
V
MODE
NC,NC/9M,
NC/18M.
NC/72M,
NC/144M,
NC/288M,
NC/576M,
NC/1G
DD
SS
DDQ
SSQ
Name
Asynchronous
Power Supply Power supply inputs to the core of the device.
Synchronous
Synchronous
Synchronous
Synchronous
I/O Ground
I/O Power
Ground
Supply
Input-
Input-
Input-
Input-
Input-
Static
(continued)
I/O-
I/O
–
Advance Input signal, sampled on the rising edge of CLK, active LOW. When asserted, it
automatically increments the address in a burst cycle.
Address Strobe from Processor, sampled on the rising edge of CLK, active LOW. When
asserted LOW, addresses presented to the device are captured in the address registers. A1, A0
are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is
recognized. ASDP is ignored when CE
Address Strobe from Controller, sampled on the rising edge of CLK, active LOW. When
asserted LOW, addresses presented to the device are captured in the address registers. A1, A0
are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is
recognized.
ZZ “sleep” Input, active HIGH. When asserted HIGH places the device in a non-time-critical
“sleep” condition with data integrity preserved. For normal operation, this pin has to be LOW or
left floating. ZZ pin has an internal pull-down.
Bidirectional Data I/O lines. As inputs, they feed into an on-chip data register that is triggered
by the rising edge of CLK. As outputs, they deliver the data contained in the memory location
specified by the addresses presented during the previous clock rise of the read cycle. The direction
of the pins is controlled by OE. When OE is asserted LOW, the pins behave as outputs. When
HIGH, DQs are placed in a tri-state condition.
Ground for the core of the device.
Power supply for the I/O circuitry.
Ground for the I/O circuitry.
Selects Burst Order. When tied to GND selects linear burst sequence. When tied to V
floating selects interleaved burst sequence. This is a strap pin and should remain static during
device operation. Mode Pin has an internal pull-up.
No Connects. Not internally connected to the die. NC/9M, NC/18M, NC/72M, NC/144M,
NC/288M, NC/576M and NC/1G are address expansion pins are not internally connected to the
die.
[A:D]
) inputs. A Global Write
CO
) is 2.6 ns
all four bytes. All writes are simplified with on-chip
synchronous self-timed Write circuitry.
Three synchronous Chip Selects (CE
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. ADSP is ignored if CE
is HIGH.
Single Read Accesses
This access is initiated when the following conditions are
satisfied at clock rise: (1) ADSP or ADSC is asserted LOW, (2)
CE
signals (GW, BWE) are all deserted HIGH. ADSP is ignored if
CE
is stored into the address advancement logic and the Address
Register while being presented to the memory array. The
corresponding data is allowed to propagate to the input of the
Output Registers. At the rising edge of the next clock the data
is allowed to propagate through the output register and onto
the data bus within 2.6 ns (250-MHz device) if OE is active
LOW. The only exception occurs when the SRAM is emerging
from a deselected state to a selected state, its outputs are
always tri-stated during the first cycle of the access. After the
first cycle of the access, the outputs are controlled by the OE
1
1
1
, CE
is HIGH. The address presented to the address inputs (A)
is deasserted HIGH.
Description
2
, CE
3
are all asserted active, and (3) the Write
1
, CE
CY7C1339G
2
, CE
Page 4 of 18
3
DD
) and an
or left
1
[+] Feedback