TLE6288R Infineon Technologies, TLE6288R Datasheet - Page 14

• Manufacturer Part Number: TLE6288R
• Description: IC SW SMART MULTICHAN PDSO36
• Manufacturer: Infineon Technologies
• Type: High Side/Low Side Driverr

Specifications of TLE6288R

• Input Type: SPI
• Number Of Outputs: 6
• On-state Resistance: 350 mOhm
• Current - Output / Channel: 2A
• Current - Peak Output: 3.6A
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Package / Case: DSO-36
• Switch Type: High Side/Low Side
• Power Switch Family: TLE 6288 R
• Power Switch On Resistance: 150mOhm
• Mounting: Surface Mount
• Supply Current: 10mA
• Package Type: DSO
• Operating Temperature (min): -40C
• Operating Temperature (max): 150C
• Operating Temperature Classification: Automotive
• Propagation Delay Time: 200ns
• Pin Count: 36
• Power Dissipation: 800mW
• Packages: PG-DSO-36
• Channels: 6.0
• Output Current: 2.0
• Rds (on): 150 mOhm
• Quiescent Current (max.): 0,05 mA
• Operating Range: 6.0 - 16.0 V
• For Use With: DEMOBOARDTLE6288RIN - BOARD DEMO FOR TLE 6288R
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: SP000013727; TLE6288RNT; TLE6288RT; TLE6288RT

4.3
The TLE6288R has a parallel diagnosis via 6 output pind (DIAG1 - DIAG6) and a serial diagnosis functionallity via
SPI.
4.3.1
Parallel diagnostic pins (push-pull) change state according to the input signal of the corresponding channel. As
soon as an error occurs at the corresponding channel (overload and overtemperature is detected in on state and
open load/switch bypass in off state) the DIAG output shows the inverted input signal. An fault is detected only if
it lasts for longer than the fault filter time. The fault information is not latched in a register.
If DIAG6 is configured as Overtemperature Flag: This is a general fault pin which shows a high to low transition
as soon as an overtemperature error occurs for any one of the six channels (for longer than the fault filter time) or
the IC logic. This fault indication can be used to differ between overload and overtemperature errors in one of the
six channels or to detect a general IC overtemperature.
4.3.2
Electrical Characteristics: Diagnostic Functions
V
ground, positive current flowing into pin (unless otherwise specified)
Pos.
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
4.3.7
4.3.8
Data Sheet
CC
= 4.5 V to 5.5 V,
Parameter
Open Load Detection Voltage
Open Load Detection Voltage
Output Open Load diagnosis
Current
Fault Filter Time
Switch Bypass Detection
Current
Overload Detection Threshold
(Channel 1 to 3)
Overload / low inductance
load Detection time
(Channel 1 to 3)
Overload Detection Threshold
(Channel 4 to 6)
Diagnostic
Parallel Diagnostic Functions
Electrical Characteristics: Diagnostic Functions
T
j
= -40 °C to +150 °C,
Symbol
V
V
I
t
I
I
t
I
f(fault)
li
d(OL)
d(SB)
Dd(lim1-3)
Dd(lim 4-6)
DS(OL)
DS(OL)
V
B
= 6 V to 16 V, Reset = H,
Min.
–
–
-500
50
–
4
–
3
14
Limit Values
Typ.
5.5
4.5
-100
100
–
–
–
–
–
–
-20
200
250
6
t
6
Max.
fo
V
DO
Unit Pin/
V
V
µA
µs
µA
A
µs
A
=
V
CC
Comment
–
–
–
–
–
–
see
Chapter 7.3
–
, all voltages with respect to
Rev. 2.4, 2007-08-08
Conditions
lowside
configuration,
V
highside
configuration,
V
V
V
–
–
no regulation
mode
current
control mode
–
B
B
B
TLE6288R
Description
=
= 12 V
= 12 V
V
out
= 12