LTC1966CMS8#TRPBF Linear Technology, LTC1966CMS8#TRPBF Datasheet - Page 16

• Manufacturer Part Number: LTC1966CMS8#TRPBF
• Description: IC PREC RMS/DC CONV MCRPWR 8MSOP
• Manufacturer: Linear Technology

Specifications of LTC1966CMS8#TRPBF

• Current - Supply: 155µA
• Voltage - Supply: 2.7 V ~ 5.5 V
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

In any configuration, the averaging capacitor should be
connected between Pins 5 and 6. The LTC1966 RMS DC
output will be a positive voltage created at V
with respect to OUT RTN (Pin 6).
Power Supply Bypassing
The LTC1966 is a switched capacitor device, and large
transient power supply currents will be drawn as the
switching occurs. For reliable operation, standard power
supply bypassing must be included. For single supply
operation, a 0.01µF capacitor from V
(Pin 1) located close to the device will suffice. For dual
supplies, add a second 0.01µF capacitor from V
to GND (Pin 1), located close to the device. If there is a
good quality ground plane available, the capacitors can go
directly to that instead. Power supply bypass capacitors
can, of course, be inexpensive ceramic types.
The sampling clock of the LTC1966 operates at approxi-
mately 200kHz, and most operations repeat at a rate of
100kHz. If this internal clock becomes synchronized to a
multiple or submultiple of the input frequency, significant
conversion error could occur. This is particularly important
when frequencies exceeding 10kHz can be injected into
the LTC1966 via supply or ground bounce. To minimize
this possibility, capacitive bypassing is recommended on
both supplies with capacitors placed immediately adjacent
to the LTC1966. For best results, the bypass capacitors
should be separately routed from Pin 7 to Pin 1, and from
Pin 4 to Pin 1.
The LTC1966 needs at least 2.7V for its power supply,
more for dual supply configurations. The range of allow-
able negative supply voltages (V
voltages (V
V
The LTC1966 has internal ESD absorption devices, which
are referenced to the V
in-circuit ESD immunity, the V
connected to a low external impedance. This can be ac-
complished with low impedance power planes or simply
with the recommended 0.01µF decoupling to ground on
each supply.
LTC1966
applicaTions inForMaTion
16
SS
– 3 • (V
constraint is:
DD
DD
– 2.7V) ≤ V
) is shown in Figure 10. Mathematically, the
DD
SS
and V
≤ GND
DD
SS
SS
and V
supplies. For effective
) vs positive supply
DD
SS
(Pin 7) to GND
pins must be
OUT
SS
(Pin 5)
(Pin 4)
Up and Running!
If you have followed along this far, you should have the
LTC1966 up and running by now! Don’t forget to enable
the device by grounding Pin 8, or driving it with a logic low.
Keep in mind that the LTC1966 output impedance is fairly
high, and that even the standard 10MΩ input impedance of
a digital multimeter (DMM) or a 10× scope probe will load
down the output enough to degrade its typical gain error
of 0.1%. In the end application circuit, either a buffer or
another component with an extremely high input impedance
(such as a dual slope integrating ADC) should be used.
For laboratory evaluation, it may suffice to use a bench
top DMM with the ability to disconnect the 10MΩ shunt.
If you are still having trouble, it may be helpful to skip
ahead a few pages and review the Troubleshooting Guide.
What About Response Time?
With a large value averaging capacitor, the LTC1966 can
easily perform RMS-to-DC conversion on low frequency
signals. It compares quite favorably in this regard to
prior generation products because nothing about the ∆S
circuitry is temperature sensitive. So the RMS result doesn’t
get distorted by signal driven thermal fluctuations like a
log/antilog circuit output does.
However, using large value capacitors results in a slow
response time. Figure 11 shows the rising and falling
step responses with a 1µF averaging capacitor. Although
they both appear at first glance to be standard exponential
–1
–2
–3
–4
–5
–6
0
2.5
Figure 10. V
3
3.5
OPERATES IN THIS RANGE
V
SS
DD
4
Limits vs V
(V)
LTC1966
4.5
5
DD
1966 F10
5.5
1966fb