ADT7460ARQZ ON Semiconductor, ADT7460ARQZ Datasheet - Page 26

• Manufacturer Part Number: ADT7460ARQZ
• Description: IC REMOTE THRML/FAN CTRLR 16QSOP
• Manufacturer: ON Semiconductor
• Series: dBCool®r

Specifications of ADT7460ARQZ

• Function: Fan Control, Temp Monitor
• Topology: ADC, Comparator, Multiplexer, Register Bank
• Sensor Type: External & Internal
• Sensing Temperature: -40°C ~ 120°C, External Sensor
• Output Type: SMBus™
• Output Alarm: No
• Output Fan: Yes
• Voltage - Supply: 3 V ~ 5.5 V
• Operating Temperature: -40°C ~ 120°C
• Mounting Type: Surface Mount
• Package / Case: 16-QSOP
• Full Temp Accuracy: +/- 3 C
• Digital Output - Bus Interface: Serial (3-Wire)
• Maximum Operating Temperature: + 120 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADT7460
Configuring the Desired THERM Behavior
1.
2.
3.
4.
5.
Configure the THERM input.
Setting Bit 1 ( THERM ENABLE) of Configuration
Register 3 (Reg. 0x78) enables the THERM monitoring
function.
Select the desired fan behavior for THERM events.
Setting Bit 2 (BOOST bit) of Configuration Register 3
(Reg. 0x78) causes all fans to run at 100% duty cycle
whenever THERM is asserted. This allows fail-safe syst
cooling. If this bit = 0, the fans run at their current set
and are not affected by
Select whether THERM events should generate
SMBALERT interrupts.
Bit 5 (F4P) of Mask Register 2 (Reg. 0x75), when set, ma
out
This bit should be cleared if SMBALERT s based on THERM
events are required.
Select a suitable THERM limit value.
This value determines whether an SMBALERT is generated
on the first THERM assertion, or only if a cumulative
THERM assertion time limit is exceeded. A value of 0x00
causes an SMBALERT to be generated on the first THERM
assertion.
Select a THERM monitoring time.
This is how often OS or BIOS level software checks the
THERM timer. For example, BIOS could read the THERM
timer once an hour to determine the cumulative THERM
assertion time. If, for example, the total THERM assertion
time is <22.76 ms in Hour 1, >182.08 ms in Hour 2, and
>5.825 s in Hour 3, this can indicate that system perfor -
a
more frequently on an hourly basis.
Alternatively, OS or BIOS level software can time-stamp
when the system is powered on. If an SMBALERT is
generated due to the THERM limit being exceeded,
another time-stamp can be taken. The difference in time
can be calculated for a fixed THERM limit time. For
example, if it takes one week for a THERM limit o
to be exceeded and the next time it takes only one hour,
this indicates a serious degradation in system performance.
nce is degrading significantly since THERM is asserting
SMBALERT s when the THERM limit value is exceeded.
THERM events.
f 2.914 s
tings
m
em
Rev. C | Page 26 of 52
sks
Configuring the ADT7460 THERM Pin as an Output
In addition to the ADT7460 being able to monitor THERM as
an input, the ADT7460 can optionally drive THERM low as a
output. The user can preprogram system critical thermal limi
If the temperature exceeds a thermal limit by 0.25°C,
asserts low. If the temperature is still a
the next monitoring cycle, THERM stays low. THERM remains
asserted low until the temperature is equal to or below the
thermal limit. Since the temperature for that channel is measured
only every monitoring cycle, on
teed to remain low for at least one monitoring cycle.
The THERM pin can be configured to assert low if the Remote 1,
local, or Remote 2 temperature THERM limits are exceeded by
0.25°C. The THERM limit registers are at Locations 0x6A,
0x6B, and 0x6C, respectively. Setting Bit 3 of Registers 0x5F,
0x60, and 0x61 enables the THERM output feature for the
Remote 1, local, and Remote 2 temperature channels, respectively.
Figure 40 shows how the THERM pin asserts low as an output
in the event of a critical overtemperature.
Figure 40. Asserting
THERM
THERM LIMIT
THERM LIMIT
0.25°C
TEMP
THERM as an Output, Based on Tripping THERM Limits
MONITORING
ADT7460
CYCLE
ce
THERM
bove the thermal limit on
asserts, it is guaran-
THERM
ts.
n