ADT7460ARQZ ON Semiconductor, ADT7460ARQZ Datasheet - Page 45
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
ADT7460ARQZ
Manufacturer Part Number
ADT7460ARQZ
Description
IC REMOTE THRML/FAN CTRLR 16QSOP
Manufacturer
ON Semiconductor
Series
dBCool®r
Specifications of ADT7460ARQZ
Function
Fan Control, Temp Monitor
Topology
ADC, Comparator, Multiplexer, Register Bank
Sensor Type
External & Internal
Sensing Temperature
-40°C ~ 120°C, External Sensor
Output Type
SMBus™
Output Alarm
No
Output Fan
Yes
Voltage - Supply
3 V ~ 5.5 V
Operating Temperature
-40°C ~ 120°C
Mounting Type
Surface Mount
Package / Case
16-QSOP
Full Temp Accuracy
+/- 3 C
Digital Output - Bus Interface
Serial (3-Wire)
Maximum Operating Temperature
+ 120 C
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ADT7460ARQZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
ADT7460ARQZ-REEL
Manufacturer:
ST
Quantity:
16
Table 63. T
Register Address
0x67
0x68
0x69
These are the T
minimum speed and increase with temperature according to T
These r
e
Table 64. THERM Limit Registers
Register Address
0x6A
0x6B
0x6C
If any temperature measured exceeds its THERM limit, all PWM outputs drive their fans at 100% duty cycle. This is a fail-safe mechanism
inco
o
T
to assert low as an output.
These registers become rea -only when the Configuration Register 1 Lock bit is s
no effect.
Table 65. Temperature Hysteresis Registers
Register Address
0x6D
0x6E
Each 4-bit value controls the amount of temperature hysteresis applied to a particular temperature channel. Once the temperature for that
channel falls below its T
hysteresis may be assigned to any temperature channel. The hysteresis value chosen also applies to that temperature channel if its THERM
limit is exceeded. The PWM output being controlled goes to 100% if the THERM limit is exceeded and remains at 100% until the
temperature drops below THERM – Hysteresis. For acoustic reasons, it is recommended that the hysteresis value not be programmed less
than 4°C. Setting the hysteresis value lower than 4°C causes the fan to switch on and off regularly when the temperature is close to T
These registers become read-only when the Configuration Register 1 lock bit is set to 1. Further attempts to write to these registers have
no effect.
Table 66. XNOR Tree Test Enable Register (Power-On Default = 0x00)
Register Address
0x6F
This register becomes read-only when the Configuration Register 1 lock bit is set to 1. Further attempts to write to this register have no
effect.
ffect.
r hardware locks up. If set to 0x80, this feature is disabled. The PWM output remains at 100% until the temperature drops below
HERM
rporated to cool the system in the event of a critical overtemperature. It also ensures some level of cooling in the event that software
egisters become read-only when the Configuration Register 1 lock bit is set. Further attempts to write to these registers have no
Limit – Hysteresis. If the THERM pin is programmed as an output, exceeding these limits by 0.25°C can cause the THERM pin
MIN
Registers
MIN
registers for each temperature channel. When the temperature measured exceeds T
R/W
Read/Write
MIN
d
value, the fan remains running at PWM
R/W
Read/Write
Read/Write
R/W
Read/Write
Read/Write
Read/Write
R/W
Read
Read/Write
Read/Write
/Write
Description
XNOR Tree Test Enable
Bit
<0>
<7:1>
Description
Remote 1 Local Temperature Hysteresis
Remote 2 Temperature Hysteresis
Mnmeonic
XEN
RES
Descrip
Remote 1 THERM Limit
Local THERM Limit
Remote 2 THERM Limit
Description
Remote 1 T
Local Temperature T
Remote 2 Temperature T
Rev. C | Page 45 of 52
RANGE
tion
MIN
.
Description
If the XEN bit is set to 1, the device enters the XNOR tree test mode.
Clearing the bit removes the device from the XNOR test mode.
Unused. Do not write to these bits.
duty cycle until the temperature = T
emperature T
MIN
et to 1. Further attempts to write to these registers have
MIN
MIN
Power-On Default
0x64 (100°C)
0x64 (100°C)
0x64 (100°C)
Power-On Default
0x44
0x40
MIN
Power-On Default
0x5A (90°C)
0x5A (90°C)
0x5A (90°C)
, the appropriate fan runs at
MIN
– Hysteresis. Up to 15°C of
ADT7460
MIN.