LM3481MMX/NOPB National Semiconductor, LM3481MMX/NOPB Datasheet - Page 19
![IC CTLR N-CH LOW SIDE HE 10MSOP](/photos/6/60/66087/pkg_mub10a_sml.jpg)
LM3481MMX/NOPB
Manufacturer Part Number
LM3481MMX/NOPB
Description
IC CTLR N-CH LOW SIDE HE 10MSOP
Manufacturer
National Semiconductor
Type
Step-Up (Boost), Flyback, Sepicr
Datasheet
1.LM3481MMNOPB.pdf
(22 pages)
Specifications of LM3481MMX/NOPB
Internal Switch(s)
No
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
Adjustable
Current - Output
1A
Frequency - Switching
100kHz ~ 1MHz
Voltage - Input
2.97 ~ 48 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
10-MSOP, Micro10™, 10-uMAX, 10-uSOP
For Use With
LM3481EVAL - BOARD EVAL FOR LM3481
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Other names
LM3481MMX
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM3481MMX/NOPB
Manufacturer:
TI
Quantity:
12 000
SELECTION OF INDUCTORS L1 AND L2
Proper selection of the inductors L1 and L2 to maintain con-
stant current mode requires calculations of the following pa-
rameters.
Average current in the inductors:
Peak to peak ripple current, to calculate core loss if neces-
sary:
Maintaining the condition I
duction mode yields the following minimum values for L1 and
L2:
Peak current in the inductor, to ensure the inductor does not
saturate:
I
the current sense resistor.
The value of L1 can be increased above the minimum rec-
ommended value to reduce input ripple and output ripple.
However, once ΔI
output ripple is minimal.
By increasing the value of L2 above the minimum recommen-
dation, ΔI
output ripple voltage:
where ESR is the effective series resistance of the output ca-
pacitor.
L1PK
must be lower than the maximum current rating set by
L2
can be reduced, which in turn will reduce the
L1
is less than 20% of I
I
L2AVE
L
> ΔI
= I
L
/2 to ensure continuous con-
OUT
L1AVE
, the benefit to
19
If L1 and L2 are wound on the same core, then L1 = L2 = L.
All the equations above will hold true if the inductance is re-
placed by 2L. A good choice for transformer with equal turns
is Coiltronics CTX series Octopack.
SENSE RESISTOR SELECTION
The peak current through the switch, I
using the current sense resistor, R
output current. Resistor R
mula:
Sepic Capacitor Selection
The selection of SEPIC capacitor, C
current. The rms current of the SEPIC capacitor is given by:
The SEPIC capacitor must be rated for a large ACrms current
relative to the output power. This property makes the SEPIC
much better suited to lower power applications where the rms
current through the capacitor is small (relative to capacitor
technology). The voltage rating of the SEPIC capacitor must
be greater than the maximum input voltage. Tantalum capac-
itors are the best choice for SMT, having high rms current
ratings relative to size. Ceramic capacitors could be used, but
the low C values will tend to cause larger changes in voltage
across the capacitor due to the large currents, and high C
value ceramics are expensive. Electrolytics work well for
through hole applications where the size required to meet the
rms current rating can be accommodated. There is an energy
balance between C
the value of the capacitor. The basic energy balance equation
is:
Where
is the ripple voltage across the SEPIC capacitor, and
is the ripple current through the inductor L1. The energy bal-
ance equation can be solved to provide a minimum value for
C
S
:
S
and L1, which can be used to determine
SEN
can be selected using the for-
SEN
SWPEAK
S
, depends on the rms
, to provide a certain
, can be adjusted
www.national.com