AFCT-5805DZ Avago Technologies US Inc., AFCT-5805DZ Datasheet - Page 2

• Manufacturer Part Number: AFCT-5805DZ
• Description: TXRX OPT SM 155MBS SONET OC3/SDH
• Manufacturer: Avago Technologies US Inc.

Specifications of AFCT-5805DZ

• Applications: General Purpose
• Data Rate: 155Mbps
• Wavelength: 1300nm
• Voltage - Supply: *
• Connector Type: SC
• Mounting Type: Through Hole
• Data Rate Max: 0.155Gbps
• Supply Voltage: 5V
• Wavelength Typ: 1300nm
• Peak Reflow Compatible (260 C): Yes
• Optical Fiber Type: TX/RX
• Data Transfer Rate: 155Mbps
• Optical Rise Time: 2/2.2ns
• Optical Fall Time: 2/2.2ns
• Operating Temperature Classification: Commercial
• Peak Wavelength: 1360nm
• Operating Supply Voltage (min): 3.1V
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.25V
• Operating Temp Range: 0C to 70C
• Mounting: Through Hole
• Pin Count: 9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Figure 1. Block Diagram
Receiver Signal Detect
Signal Detect is a basic fiber failure indicator. This is a
single-ended PECL output. As the input optical power
is decreased, Signal Detect will switch from high to low
(deassert point) somewhere between sensitivity and
the no light input level. As the input optical power is
increased from very low levels, Signal Detect will switch
back from low to high (assert point). The assert level will be
at least 0.5 dB higher than the deassert level.
Transceiver Specified for Wide Temperature Range Operation
The AFCT-5805xxZ is specified for operation over ex-
tended temperature range of -40° to +85°C.
Characterization of the parts has been performed over
the ambient operating temperature range in an airflow
of 2 m/s.
Other Members of Avago Technologies SC Duplex
155 Mb/s Product Family
• HFCT-5801, 1300 nm single mode transceiver for

DATA
DATA
SIGNAL DETECT
DATA
DATA
links up to 15 km. The part is based on the 2 x 9 in-
dustry standard package and has laser bias, optical
power monitor and transmitter disable functions.
ELECTRICAL SUBASSEMBLY
AMPLIFIER IC
DRIVER
LASER
POST
IC
ASSEMBLIES
AMPLIFIER
PRE-
OPTICAL
TOP VIEW
LASER
IC
SUB-
PIN PHOTODIODE
Applications Information
Typical BER Performance of Receiver versus Input Optical
Power Level
The AFCT-5805xxZ transceiver can be operated at
Bit-Error-Rate conditions other than the required BER =
1 x 10
Standard. The typical trade-off of BER versus Relative In-
put Optical Power is shown in Figure 2. The Relative Input
Optical Power in dB is referenced to the actual sensitivity
of the device. For BER conditions better than 1 x 10
more input signal is needed (+dB).
Figure 2. Relative Input Optical Power - dBm. Avg.
10
10
10
10
10
10
10
10
10
10
10
10
10
10
-10
-11
-12
-13
-14
-15
DUPLEX SC
RECEPTACLE
-2
-3
-4
-5
-6
-7
-8
-9
-10
-5 -4 -3 -2 -1 0
of the ATM Forum 155.52 Mb/s Physical Layer
LINEAR EXTRAPOLATION OF
10
-4
THROUGH 10
ACTUAL DATA
BASED ON
-7
DATA
1
2
3
-10
,