ZUP10-20/U TDK Corporation, ZUP10-20/U Datasheet - Page 35

• Manufacturer Part Number: ZUP10-20/U
• Description: PWR SUP BENCH PROG 0-10V 200W
• Manufacturer: TDK Corporation
• Series: ZUPr
• Type: Enclosedr

Specifications of ZUP10-20/U

• Number Of Outputs: 1
• Efficiency: 77%
• Voltage - Output: 0 ~ 10V
• Power (watts): 200W
• Applications: Commercial
• Power Supply Type: Switching (Closed Frame)
• Voltage - Input: 85 ~ 265VAC
• Mounting Type: Chassis Mount
• 1st Output: 0 ~ 10 VDC @ 20A
• Size / Dimension: 13.78" L x 4.88" W x 2.76" H (350mm x 124mm x 70mm)
• Power (watts) - Rated: 200W
• Operating Temperature: 0°C ~ 50°C
• Approvals: CE, EN, UL
• Line Regulation: 0.01%
• Load Regulation: 0.01%
• Output Current (max): 20A
• Input Voltage: 85 to 265V
• Output Power (max): 200W
• Input Frequency: 47 to 63Hz
• Screening Level: Commercial
• Operating Temperature Min Deg. C: 0C
• Operating Temperature Max Deg. C: 50C
• Mounting Style: Desktop
• Accuracy: 0.02% + 8 mV
• Brand/series: ZUP
• Current, Output: 20 A
• Display Type: Digital Meter
• Power, Output: 200 W
• Power, Rating: 200 W (Max.)
• Regulation, Line: 0.01% + 2 mA⁄1 mV + 0.005%
• Regulation, Load: 0.01% + 5 mA⁄2 mV + 0.005%
• Standards: UL Listed, CE Marked
• Temperature Coefficient: 30 ppm⁄°C (CV)⁄100 ppm⁄°C (CC)
• Temperature, Operating, Maximum: 50 °C
• Temperature, Operating, Minimum: 0 °C
• Voltage, Input: 85-265 VAC
• Voltage, Noise: 50 mV @ 20 MHz BW
• Voltage, Output: 10 VDC
• Voltage, Ripple: 5 mV @ 5 Hz to 1 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: 285-1668; Q1074270; ZUP10-20/U; ZUP1020/U

4.4.7 Foldback Protection
1. Foldback protection will shut down the power supply output if the load current exceeds the current
2. To arm the Foldback protection, the FOLD pushbutton should be pressed so the FOLD LED
3. Activation of the Foldback protection disables the power supply’s output, turns on the ALM (alarm)
4. There are 2 modes of releasing an activated Foldback protection.
4.4.8 Output ON/OFF Control
The ON/OFF circuit has two controls; a front panel pushbutton and a rear panel connection. priority is
given to the rear panel connection.
2. Front panel ON/OFF Control
1. Rear panel ON/OFF Control
Contacts 9, 10 at the rear panel External Control connector (fig. 4-2, item 4) serve as ON/OFF
terminals. Either short circuit or TTL ‘0’ level enables the power supply output and open circuit or TTL ‘1’
level disables the power supply’s output. An open collector transistor can be used for the ON/OFF
control as shown in fig. 4-3, with sink current ability of more than 2.5mA. Please note that pin 10 (COM)
is internally connected to the - Sense potential, therefore for floating ON/OFF Control a photocoupler
should be used as shown in Fig. 4-4.
Fig. 4-3: ON/OFF Control, references to - Sense.
The Front Panel ON/OFF is controlled by the OUT pushbutton. To enable the output, OUT pushbutton
should be pressed so that OUT LED illuminates. The operation of OUT pushbutton is enabled only if the
rear panel ON/OFF is configured to ‘ON’.
COM
VCVP
VCCP
RCCP
- S
+S
limit setting level. This protection is useful when the load circuitry is sensitive to over current
condition.
1. Short press on FOLD pushbutton enables the output and re-arms the protection circuit. If the load
2. Long press (approx. 3sec) on FOLD pushbutton will disable the Foldback protection circuit and
P
illuminates. At this condition transition from Constant Voltage to Constant Current mode will activate
the Foldback protection.
LED and flashes the FOLD LED.
is smaller than the current limit level, the power supply will restore normal operation. If the load is
greater than the current limit level, the output will be disabled again and Foldback indicators will
be on.
enable the output. The power supply will restore operation to Constant Voltage or Constant
Current mode depending on the load characteristics and power supply setting.
2
1
(ZUP rear panel view)
VRFV
VRFI
RCVP
- LS
+LS
On/Off
2.5mA
Output Good
ON
OFF
COM
VCVP
VCCP
RCCP
- S
+S
P
2
1
On/Off
VRFV
VRFI
RCVP
- LS
+LS
Fig. 4-4: Floating ON/OFF Control
Output Good
(ZUP rear panel view)
ON
OFF