MPC5553EVB Freescale Semiconductor, MPC5553EVB Datasheet - Page 62

• Manufacturer Part Number: MPC5553EVB
• Description: KIT EVAL MPC5553MZP132
• Manufacturer: Freescale Semiconductor
• Type: Microcontrollerr

Specifications of MPC5553EVB

• Contents: Eval Board and Demo Software
• Processor To Be Evaluated: MPC55xx
• Data Bus Width: 32 bit
• Interface Type: RS-232, Ethernet
• For Use With/related Products: MPC5553
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Revision History for the MPC5553 Data Sheet
The following table describes the changes made to information in tables and figures, and is presented in
sequential page number order.
62
Figure 1
Table 1
Table 2
Table 4
Table 5
Table
Location
6, VCR/POR Electrical Specifications:
Orderable Part Numbers:
EMI Testing Specifications: Changed the maximum operating frequency to from 132 to f
ESD Characteristics: Added (Electromagnetic Static Discharge) in the section title.
Absolute Maximum Ratings:
MPC5500 Family Part Numbers:
• Removed the 2 in the tape and reel designator in both the graphic and in the Tape and Reel Status text.
• Changed Qualification Status by adding ‘, general market flow’ to the M designator, and added an ‘S’ designator
• Moved the ‘Lead-free’ or ‘Lead’ in the Package Description column to a second line and added ‘Pb-free’ and
• Footnote 2 changed to read:’ The lowest ambient operating temperature is referenced by T
• Footnote 3 changed to read: ‘Speed is the nominal maximum frequency. Max speed is the maximum speed
• Deleted Spec 3, “Flash core voltage.”
• Spec 21, Added the name of the spec, ‘V
• Spec 28 “Maximum Solder Temperature”: Added two lines:
• Footnote 1, added: ‘any of’ between ‘beyond’ and ‘the listed maxima.’
• Deleted footnote 2: ‘Absolute maximum voltages are currently maximum burn-in voltages. Absolute maximum
• Footnote 6 (now footnote 5): Changed to the following sentence to the end, “Internal structures hold the input
• Subscript all symbol names that appear after the first underscore character.
• Removed ‘Tj ‘ after ‘150 C’ in the last line, second column: Characteristic.
• Reformatted columns.
• Added footnote 1 to specs 1, 2, and 3 that reads: On power up, assert RESET before V
• Added to Spec 2:
• Specs 7 and 10: added ‘at Tj ‘ at the end of the first line in the second column: Characteristic.
• Spec 10:
• Added a new footnote 7, ‘Refer to
• Rewrote old footnote 8 (new footnote 9) to read: Represents the worst-case external transistor BETA. It is
• Deleted old footnote 9: ‘Preliminary value. Final specification pending characterization.’
with the description of ‘Fully spec. qualified, automotive flow.
‘SnPb’ respectively. Changed Lead to Leaded.
operating temperature is referenced by T
allowed including frequency modulation (FM): 82 MHz parts allow for 80 MHz system clock + 2% FM; 114 MHz
parts allow for 112 MHz system clock + 2% FM; and 132 MHz parts allow for 128 MHz system clock + 2% FM;.’
reference to
Lead-free (Pb-free) and Leaded (SnPb) with maximum values of 260 C and 245 C respectively.
specifications for device stress have not yet been determined.’
voltage greater than -1.0 V if the injection current limit of 2 mA is met. Keep the negative DC voltage greater than
-0.6 V on eTPU[15] and on SINB during the internal power-on reset (POR) state.”
negate (internal POR). RESET must remain asserted until the power supplies are within the operating conditions
as specified in
fall outside the operating conditions and until the internal POR asserts.
measured on a per-part basis and calculated as (I
3.3 V (V
3.3 V (V
• Changed the minimum values of: -40 C = 40; 25 C = 45; 150 C = 55.
• Added cross-reference to footnote 6: ‘I
V
RC33
DDSYN
DDSYN
= 3.1 V, V
Table 33. Table and Figure Changes Between Rev. 2.0 and 3.0
Table
) POR negated (ramp down)
) POR asserted (ramp up)
Table 9
9, DC Electrical Specifications, to which the Spec was moved.
VRCCTL
DC Electrical Specifications. On power down, assert RESET before any power supplies
MPC5553 Microcontroller Data Sheet, Rev. 3.0
= 2.2 V.’ Changed ‘(@ V
Table 1
H
RC33
VRCCTL
Description of Changes
.’
for the maximum operating frequency.’
to V
is measured at the following conditions: V
DD
DDSYN
DD
Min. 0.0
÷
= 1.35 V, f
Min. 0.0
I
VRCCTL
differential voltage,’ as well as the name and cross
).
sys
Max 0.30
= f
Max 0.30
MAX
)‘ to ‘(@ f
V
V
MAX
sys
.
POR15
Freescale Semiconductor
= f
MAX
L
; the highest ambient
, V
DD
).
POR33
= 1.35 V,
, and V
POR5