1213563-1 Tyco Electronics, 1213563-1 Datasheet

no-image

1213563-1

Manufacturer Part Number
1213563-1
Description
TOOL DAHT ADAPTER ASSEMBLY
Manufacturer
Tyco Electronics
Datasheet
1.1213563-1.pdf (5 pages)

Specifications of 1213563-1

Connector Type
DAHT Adaptor
Lead Free Status / RoHS Status
Not applicable / Not applicable
Crimp Handle
-
Crimp Or Cable Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
1. INTRODUCTION
DAHT (Double Action Hand Tool) Adapter Assembly
1213563–1 is designed to accept the crimp head from
any Double Action Hand Tool to adapt the crimp head
for use with 626 Pneumatic Tooling Assemblies.
Double Action Hand Tools are sold separately and are
available from Tyco Electronics. For information
concerning the setup and operation of the pneumatic
tools, refer to Customer Manual 409–5862.
This instruction sheet provides:
For crimp head information concerning wire
preparation, crimping procedures, maintenance,
inspection, and repair, refer to the associated
instruction sheet for the appropriate hand tool.
E
S
S
S
S
Recommended procedures for crimp head
removal from the hand tool
Crimp head installation into the adapter
Installation and removal of the cam and
adapter from the pneumatic tool
Maintenance, inspection, and repair information
for the adapter
DAHT Adapter Assembly 1213563-1
(Adapts Crimp Heads for Use with
626 Pneumatic Tooling Assemblies)
Figure 1
Read these instructions thoroughly before
proceeding.
Reasons for reissue of this sheet are provided in
Section 8, REVISION SUMMARY.
2. DESCRIPTION
The adapter facilitates the connection of the double
action crimp head (typical crimp head shown in
Figure 1) to the pneumatic tool and provides the
necessary motion of the crimp head jaws when the
pneumatic tool is actuated. When the tool is actuated,
the cam extends into the adapter, contacting the
crimp head jaws. When the cam retracts, the force is
removed from the jaws and they return to their
starting position.
The jaws may be opened and closed manually by
simultaneously squeezing the two opposing clevises,
which are coupled to the jaws. The quick pins secure
the crimp head to the adapter.
NOTE
i
Dimensions are in millimeters [with inch
equivalents in brackets]. Figures and illustrations
are for identification only and are not drawn to
scale.
www.tycoelectronics.com
408-4485
1

1213563-1 Summary of contents

Page 1

... For crimp head information concerning wire preparation, crimping procedures, maintenance, inspection, and repair, refer to the associated instruction sheet for the appropriate hand tool. E DAHT Adapter Assembly 1213563-1 (Adapts Crimp Heads for Use with 626 Pneumatic Tooling Assemblies) Figure 1 Read these instructions thoroughly before proceeding ...

Page 2

... DAHT Adapter Assembly 1213563-1 3. CRIMP HEAD REMOVAL FROM HAND TOOL Remove the two retaining rings from one side of the hand tool body and push the retaining pins, along with the two remaining retaining rings, through the opposite side of the tool body, as shown in Figure 2. ...

Page 3

... DAHT Adapter Assembly 1213563-1 Adapter Crimp Head (Installed) 3. Using hex wrench supplied with adapter, tighten cam setscrew, then pull on cam to ensure that it is firmly attached. 4. Properly align adapter with cam and push adapter onto power unit so that it passes over the friction ring on the power unit. ...

Page 4

... DAHT Adapter Assembly 1213563-1 3. Make certain all surfaces are protected with a thin coat of any good SAE 20 motor oil. DO NOT oil excessively. 4. When the adapter assembly is not in use, store clean, dry area. 6.2. Periodic Inspection Regular inspections should be performed by quality–control personnel. A record of scheduled ...

Page 5

... DAHT Adapter Assembly 1213563-1 ITEM PART NUMBER REPLACEMENT PARTS DESCRIPTION Figure 4 408-4485 QTY PER ASSEMBLY 5 ...