ATTINY461-20MU Atmel, ATTINY461-20MU Datasheet - Page 155

• Manufacturer Part Number: ATTINY461-20MU
• Description: IC AVR MCU 4K 20MHZ 32-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY461-20MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Processor Series: ATTINY4x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: 2-Wire, SPI, USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIPATAVRBC100 - REF DESIGN KIT BATTERY CHARGER770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

15.13 Register Description
15.13.1
2588E–AVR–08/10
ADMUX – ADC Multiplexer Selection Register
assuming calibration at room temperature. Better accuracies are achieved by using two
temperature points for calibration.
Table 15-2.
The values described in
temperature sensor output voltage varies from one chip to another. To be capable of achieving
more accurate results the temperature measurement can be calibrated in the application soft-
ware. The sofware calibration can be done using the formula:
where ADCH and ADCL are the ADC data registers, k is the fixed slope coefficient and T
the temperature sensor offset. Typically, k is very close to 1.0 and in single-point calibration the
coefficient may be omitted. Where higher accuracy is required the slope coefficient should be
evaluated based on measurements at two temperatures.
• Bits 7:6 – REFS1:REFS0: Voltage Reference Selection Bits
These bits together with the REFS2 bit from the ADC Control and Status Register B (ADCSRB)
select the voltage reference for the ADC, as shown in
Table 15-3.
If these bits are changed during a conversion, the change will not go in effect until this conver-
sion is complete (ADIF in ADCSR is set). Also note, that when these bits are changed, the next
conversion will take 25 ADC clock cycles.
Bit
0x07 (0x27)
Read/Write
Initial Value
Temperature
ADC
T = k * [(ADCH << 8) | ADCL] + T
REFS2
X
X
0
0
1
1
Temperature vs. Sensor Output Voltage (Typical Case)
Voltage Reference Selections for ADC
REFS1
R/W
7
0
REFS1
0
0
1
1
1
1
REFS0
Table 15-2
R/W
6
0
230 LSB
-40 °C
ADLAR
REFS0
R/W
5
0
0
1
0
1
0
1
are typical values. However, due to process variation the
MUX4
OS
R/W
4
0
Voltage Reference Selection
V
disconnected from AREF
External voltage reference at AREF pin,
internal voltage reference turned off
Internal 1.1V voltage reference
Reserved
Internal 2.56V voltage reference,
without external bypass capacitor,
disconnected from AREF
Internal 2.56V voltage reference,
with external bypass capacitor at AREF pin
CC
used as voltage reference,
MUX3
R/W
3
0
Table
300 LSB
+25 °C
15-3.
MUX2
R/W
2
0
MUX1
R/W
1
0
MUX0
R/W
0
0
370 LSB
+85 °C
ADMUX
OS
155
is