PIC18F27J53-I/SP Microchip Technology, PIC18F27J53-I/SP Datasheet - Page 286

• Manufacturer Part Number: PIC18F27J53-I/SP
• Description: IC PIC MCU 128KB FLASH 28SPDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J53-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: *
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.8 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 8
• Operating Supply Voltage: 2.15 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• Controller Family/series: PIC18
• Cpu Speed: 48MHz
• Embedded Interface Type: I2C, SPI, USART
• Digital Ic Case Style: DIP
• Supply Voltage Range: 1.8V To 5.5V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F47J53 FAMILY
REGISTER 19-4:
19.4.7
In Single Output mode, pulse steering allows any of the
PWM pins to be the modulated signal. Additionally, the
same PWM signal can simultaneously be available on
multiple pins.
Once
(CCPxM<3:2> = 11 and PxM<1:0> = 00 of the
CCPxCON register), the user firmware can bring out
the same PWM signal to one, two, three or four output
pins by setting the appropriate STR<D:A> bits
(PSTRxCON<3:0>), as provided in Table 19-3.
DS39964B-page 286
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6-0
Note:
PxRSEN
R/W-0
the
PULSE STEERING MODE
The associated TRIS bits must be set to
output (‘0’), to enable the pin output driver,
in order to see the PWM signal on the pin.
Single
PxRSEN: PWM Restart Enable bit
1 = Upon auto-shutdown, the ECCPxASE bit clears automatically once the shutdown event goes
0 = Upon auto-shutdown, ECCPxASE must be cleared by software to restart the PWM
PxDC<6:0>: PWM Delay Count bits
PxDCn = Number of F
PxDC6
R/W-0
away; the PWM restarts automatically
ECCPxDEL: ECCP1/2/3 ENHANCED PWM CONTROL REGISTER
(1, ACCESS FBDh; 2, FB7h; 3, BANKED F18h)
Output
should transition active and the actual time it transitions active.
W = Writable bit
‘1’ = Bit is set
mode
PxDC5
R/W-0
OSC
is
/4 (4 * T
selected
PxDC4
R/W-0
Preliminary
OSC
) cycles between the scheduled time when a PWM signal
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
PxDC3
R/W-0
While the PWM Steering mode is active, the
CCPxM<1:0> bits (CCPxCON<1:0>) select the PWM
output polarity for the Px<D:A> pins.
The PWM auto-shutdown operation also applies to
PWM Steering mode, as described in Section 19.4.4
“Enhanced
auto-shutdown event will only affect pins that have
PWM outputs enabled.
PxDC2
R/W-0
PWM
Auto-shutdown
 2010 Microchip Technology Inc.
x = Bit is unknown
PxDC1
R/W-0
mode”.
PxDC0
R/W-0
bit 0
An