EP9315-CBZ Cirrus Logic Inc, EP9315-CBZ Datasheet - Page 430

• Manufacturer Part Number: EP9315-CBZ
• Description: IC ARM9 SOC ENH UNIV 352PBGA
• Manufacturer: Cirrus Logic Inc
• Series: EP9r

Specifications of EP9315-CBZ

• Core Size: 16/32-Bit
• Core Processor: ARM9
• Speed: 200MHz
• Connectivity: EBI/EMI, EIDE, Ethernet, I²C, IrDA, Keypad/Touchscreen, PCMCIA, SPI, UART/USART, USB
• Peripherals: AC'97, DMA, I&sup2:S, LCD, LED, MaverickKey, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 352-BGA
• Controller Family/series: (ARM9)
• No. Of I/o's: 16
• Cpu Speed: 200MHz
• No. Of Timers: 5
• Digital Ic Case Style: BGA
• Supply Voltage Range: 1.65V To 1.94V, 3V To 3.6V
• Embedded Interface Type: SPI
• Rohs Compliant: Yes
• Processor Series: EP93xx
• Core: ARM920T
• Data Bus Width: 32 bit
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: EDB9315A-Z
• Case: BGA
• Dc: 06+
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1144 - KIT DEVELOPMENT EP9315 ARM9
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 598-1139

10
10-36
DMA Controller
EP93xx User’s Guide
Definition:
Bit Descriptions:
This is the interrupt status register. The register is read to obtain interrupt
status for enabled interrupts. An interrupt is enabled by writing the
corresponding bits in the CONTROL register.
Write this location once to clear the interrupt. (See the Interrupt Register Bit
Descriptions for the bits where this applies.)
RSVD:
STALLInt:
DONEInt:
NFBInt:
Copyright 2007 Cirrus Logic
Reserved. Unknown During Read.
Indicates channel has stalled. This interrupt is generated
on a Channel State machine transition from MEM_RD
(memory read) or MEM_WR (memory write) to the STALL
state, assuming STALLIntEn set. The interrupt is cleared
by either disabling the channel or by triggering a new
transfer.
Transaction is done. When enabled, this interrupt is set
when all DMA controller transactions complete normally,
as determined by the transfer count/external peripheral
DEOT signal. When a transfer completes, software must
clear the DONE bit before reprogramming the DMA, by
writing either a “0” or “1” to this bit. This must be done
even if the DMA interrupt is disabled. The DMA will ignore
any additional DREQs that it receives from the external
peripheral (if operating in external DMA mode) until the
software clears the DONE interrupt and reprograms the
DMA with new BCRx values.
Indicates that a channels buffer descriptor is free for
update. This interrupt is generated if NFBIntEn is set,
when a transfer begins using the second buffer of the
double-buffer set, thus informing software that it can now
set up the other buffer. The interrupt is cleared by either
disabling the channel or writing a new BCR value to set up
a new buffer descriptor. The interrupt is not generated for
a single-buffer transfer. In software triggered M2M mode,
servicing of the NFB interrupt is dependent on the system
level AHB arbitration since the DMA’s HREQ (AHB
request) may be continuously held high.
DS785UM1