PIC18F45J10-I/PT Microchip Technology, PIC18F45J10-I/PT Datasheet - Page 142

• Manufacturer Part Number: PIC18F45J10-I/PT
• Description: IC PIC MCU FLASH 16KX16 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F45J10-I/PT

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 32
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 32
• Ram Memory Size: 1KB
• Cpu Speed: 40MHz
• No. Of Timers: 3
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1024 B
• Interface Type: MSSP, SPI, I2C, EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 100 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM163022, DM183040
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 13 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162074 - HEADER INTRFC MPLAB ICD2 44TQFPMA180013 - MODULE PLUG-IN 18F45J10 44TQFPAC162067 - HEADER INTRFC MPLAB ICD2 40/28PAC164330 - MODULE SKT FOR 44TQFP 18F45J10
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

current from destroying the bridge power switches. The
illustration. Bits PDC6:PDC0 of the ECCP1DEL register
PIC18F45J10 FAMILY
14.4.6
In half-bridge applications, where all power switches
are modulated at the PWM frequency at all times, the
power switches normally require more time to turn off
than to turn on. If both the upper and lower power
switches are switched at the same time (one turned on
and the other turned off), both switches may be on for
a short period of time until one switch completely turns
off. During this brief interval, a very high current (shoot-
through current) may flow through both power
switches, shorting the bridge supply. To avoid this
potentially destructive shoot-through current from
flowing during switching, turning on either of the power
switches is normally delayed to allow the other switch
to completely turn off.
In the Half-Bridge Output mode, a digitally programmable
dead-band delay is available to avoid shoot-through
delay occurs at the signal transition from the nonactive
state to the active state. See Figure 14-4 for an
(Register 14-2) set the delay period in terms of microcon-
troller instruction cycles (T
not available in 28-pin devices as the standard CCP
module does not support half-bridge operation.
14.4.7
When the ECCP1 is programmed for any of the
Enhanced PWM modes, the active output pins may be
configured for auto-shutdown. Auto-shutdown immedi-
ately places the Enhanced PWM output pins into a
defined shutdown state when a shutdown event occurs.
REGISTER 14-2:
DS39682D-page 140
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6-0
Note 1:
Note:
PRSEN
R/W-0
Reserved on 28-pin devices; maintain these bits clear.
PROGRAMMABLE DEAD-BAND
DELAY
Programmable dead-band delay is not
implemented in 28-pin devices with
standard CCP modules.
ENHANCED PWM AUTO-SHUTDOWN
PRSEN: PWM Restart Enable bit
1 = Upon auto-shutdown, the ECCPASE bit clears automatically once the shutdown event goes away;
0 = Upon auto-shutdown, ECCPASE must be cleared in software to restart the PWM
PDC6:PDC0: PWM Delay Count bits
Delay time, in number of F
signal to transition to active.
PDC6
R/W-0
the PWM restarts automatically
ECCP1DEL: PWM DEAD-BAND DELAY REGISTER
(1)
CY
or 4 T
W = Writable bit
‘1’ = Bit is set
PDC5
R/W-0
OSC
). These bits are
(1)
OSC
/4 (4 * T
PDC4
R/W-0
(1)
(1)
OSC
) cycles, between the scheduled and actual time for a PWM
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
PDC3
R/W-0
A shutdown event can be caused by either of the
comparator modules, a low level on the Fault input pin
(FLT0) or any combination of these three sources. The
comparators may be used to monitor a voltage input
proportional to a current being monitored in the bridge
circuit. If the voltage exceeds a threshold, the
comparator switches state and triggers a shutdown.
Alternatively, a low digital signal on FLT0 can also trigger
a shutdown. The auto-shutdown feature can be disabled
by not selecting any auto-shutdown sources. The auto-
shutdown sources to be used are selected using the
ECCPAS2:ECCPAS0 bits (bits<6:4> of the ECCP1AS
register).
When a shutdown occurs, the output pins are
asynchronously placed in their shutdown states, spec-
ified by the PSSAC1:PSSAC0 and PSSBD1:PSSBD0
bits (ECCPAS3:ECCPAS0). Each pin pair (P1A/P1C
and P1B/P1D) may be set to drive high, drive low or be
tri-stated
(ECCP1AS<7>) is also set to hold the Enhanced PWM
outputs in their shutdown states.
The ECCPASE bit is set by hardware when a shutdown
event occurs. If automatic restarts are not enabled, the
ECCPASE bit is cleared by firmware when the cause of
the shutdown clears. If automatic restarts are enabled,
the ECCPASE bit is automatically cleared when the
cause of the auto-shutdown has cleared.
If the ECCPASE bit is set when a PWM period begins,
the PWM outputs remain in their shutdown state for that
entire PWM period. When the ECCPASE bit is cleared,
the PWM outputs will return to normal operation at the
beginning of the next PWM period.
Note:
(1)
Writing to the ECCPASE bit is disabled
while a shutdown condition is active.
(not
PDC2
R/W-0
driving).
(1)
© 2008 Microchip Technology Inc.
x = Bit is unknown
PDC1
R/W-0
The
(1)
ECCPASE
PDC0
R/W-0
(1)
bit 0
bit