C8051F017-GQ Silicon Laboratories Inc, C8051F017-GQ Datasheet - Page 123

• Manufacturer Part Number: C8051F017-GQ
• Description: IC 8051 MCU 32K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F01xr

Specifications of C8051F017-GQ

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 32-LQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 8
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 4x10b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 8
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F005DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• On-chip Dac: 2-ch x 12-bit
• No. Of I/o's: 8
• Ram Memory Size: 256Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 5
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1196

17. SERIAL PERIPHERAL INTERFACE BUS
The Serial Peripheral Interface (SPI) provides access to a four-wire, full-duplex, serial bus. SPI supports the
connection of multiple slave devices to a master device on the same bus. A separate slave-select signal (NSS) is
used to select a slave device and enable a data transfer between the master and the selected slave. Multiple masters
on the same bus are also supported. Collision detection is provided when two or more masters attempt a data
transfer at the same time. The SPI can operate as either a master or a slave. When the SPI is configured as a
master, the maximum data transfer rate (bits/sec) is one-half the system clock frequency.
When the SPI is configured as a slave, the maximum data transfer rate (bits/sec) for full-duplex operation is 1/10 the
system clock frequency, provided that the master issues SCK, NSS, and the serial input data synchronously with the
system clock. If the master issues SCK, NSS, and the serial input data asynchronously, the maximum data transfer
rate (bits/sec) must be less that 1/10 the system clock frequency. In the special case where the master only wants to
transmit data to the slave and does not need to receive data from the slave (i.e. half-duplex operation), the SPI slave
can receive data at a maximum data transfer rate (bits/sec) of ¼ the system clock frequency. This is provided that
the master issues SCK, NSS, and the serial input data synchronously with the system clock.
123
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
SYSCLK
S
C
R
7
S
C
R
6
Clock Divide
SPI0CKR
S
C
R
5
SFR Bus
SPI0DAT
Write to
Logic
S
C
R
4
S
C
R
3
Data Path
Control
S
C
R
2
Receive Data Register
S
C
R
1
7
Figure 17.1. SPI Block Diagram
S
C
R
0
6
Shift Register
5
SPI CONTROL LOGIC
4
C
K
P
H
A
3
O
C
K
P
L
2
(Master Mode)
SFR Bus
SPI0CFG
SPI Clock
B
C
2
1
SPI0DAT
SPI0DAT
Read
Bit Count
B
C
1
0
Logic
B
C
0
Rev. 1.7
F
R
S
2
Tx Data
F
R
S
1
Rx Data
F
R
S
0
Pin Control
S
P
F
Control
I
Interface
Logic
Pin
W
O
C
L
M
O
D
F
SPI0CN
O
R
X
V
R
N
T
X
B
S
Y
MOSI
MISO
SCK
NSS
S
L
V
S
E
L
M
S
T
E
N
S
P
E
N
I
C
R
O
R
S
S
B
A
SPI IRQ
Port I/O