C8051F017-GQ Silicon Laboratories Inc, C8051F017-GQ Datasheet - Page 124

• Manufacturer Part Number: C8051F017-GQ
• Description: IC 8051 MCU 32K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F01xr

Specifications of C8051F017-GQ

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 32-LQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 8
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 4x10b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 8
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F005DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• On-chip Dac: 2-ch x 12-bit
• No. Of I/o's: 8
• Ram Memory Size: 256Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 5
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1196

17.1.
The four signals used by the SPI (MOSI, MISO, SCK, NSS) are described below.
17.1.1. Master Out, Slave In
The master-out, slave-in (MOSI) signal is an output from a master device and an input to slave devices. It is used to
serially transfer data from the master to the slave. Data is transferred most-significant bit first.
17.1.2. Master In, Slave Out
The master-in, slave-out (MISO) signal is an output from a slave device and an input to the master device. It is used
to serially transfer data from the slave to the master.
places the MISO pin in a high-impedance state when the slave is not selected.
17.1.3. Serial Clock
The serial clock (SCK) signal is an output from the master device and an input to slave devices. It is used to
synchronize the transfer of data between the master and slave on the MOSI and MISO lines.
17.1.4. Slave Select
The slave select (NSS) signal is an input used to select the SPI module when in slave mode by a master, or to
disable the SPI module when in master mode. When in slave mode, it is pulled low to initiate a data transfer and
remains low for the duration of the transfer.
Signal Descriptions
Master
Device
Figure 17.2. Typical SPI Interconnection
Device
Slave
NSS
Rev. 1.7
Device
Slave
NSS
Data is transferred most-significant bit first. A SPI slave
Device
Slave
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
NSS
VDD
MISO
MOSI
SCK
124