AD7265BSUZ Analog Devices Inc, AD7265BSUZ Datasheet - Page 25

• Manufacturer Part Number: AD7265BSUZ
• Description: IC,Data Acquisition System,3-CHANNEL,12-BIT,TQFP,32PIN,PLASTIC
• Manufacturer: Analog Devices Inc

Specifications of AD7265BSUZ

• Design Resources: AD7265 in Differential and Single-Ended Configurations Using AD8022 (CN0048)
• Number Of Bits: 12
• Sampling Rate (per Second): 1M
• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Converters: 2
• Power Dissipation (max): 21mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 32-TQFP, 32-VQFP
• Number Of Elements: 2
• Resolution: 12Bit
• Architecture: SAR
• Sample Rate: 1MSPS
• Input Polarity: Unipolar
• Input Type: Voltage
• Rated Input Volt: 2.5/5V
• Differential Input: Yes
• Power Supply Requirement: Analog and Digital
• Single Supply Voltage (typ): 3/5V
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.25V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 21mW
• Differential Linearity Error: -0.99LSB/1.5LSB
• Integral Nonlinearity Error: ±1.5LSB
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 32
• Package Type: TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7265CB - BOARD EVALUATION FOR AD7265
• Lead Free Status / Rohs Status: Compliant

AD7265 TO DSP563xx
The connection diagram in Figure 46 shows how the AD7265
can be connected to the ESSI (synchronous serial interface) of
the DSP563xx family of DSPs from Motorola. There are two
on-board ESSIs, and each operates in synchronous mode
(Bit SYN = 1 in CRB register) with internally generated word
length frame sync for both TX and RX (Bit FSL1 = 0 and
Bit FSL0 = 0 in CRB).
Normal operation of the ESSI is selected by making MOD = 0
in the CRB. Set the word length to 16 by setting Bit WL1 = 1
and Bit WL0 = 0 in CRA.
To implement the power-down modes on the AD7265, the
word length can be changed to 8 bits by setting Bit WL1 = 0 and
Bit WL0 = 0 in CRA. The FSP bit in the CRB should be set to 1
so the frame sync is negative. It is imperative for signal
processing applications that the frame synchronization signal
from the DSP563xx provides equidistant sampling.
Rev. A | Page 25 of 28
In the example shown in Figure 46, the serial clock is taken
from the ESSI0 so the SCK0 pin must be set as an output,
SCKD = 1, while the SCK1 pin is set as an input, SCKD = 0. The
frame sync signal is taken from SC02 on ESSI0, so SCD2 = 1,
while on ESSI1, SCD2 = 0; therefore, SC12 is configured as an
input. The V
voltage as that of the DSP563xx. This allows the ADC to operate
at a higher voltage than its serial interface and therefore the
DSP563xx, if necessary.
1
ADDITIONAL PINS OMITTED FOR CLARITY.
AD7265
Figure 46. Interfacing the AD7265 to the DSP563xx
DRIVE
D
D
V
1
SCLK
OUT
OUT
DRIVE
pin of the AD7265 takes the same supply
CS
A
B
SCK0
SCK1
SRD0
SRD1
SC02
SC12
DSP563xx
V
DD
AD7265
1