CS8422-DNZR Cirrus Logic Inc, CS8422-DNZR Datasheet - Page 12

• Manufacturer Part Number: CS8422-DNZR
• Description: IC 24-bit 192kHz SRC S/PDIF Receiver
• Manufacturer: Cirrus Logic Inc

12
MCLK_OUT
TX_SEL
RX_SEL
RCBL
C
TX/U
V_REG
VD_FILT
DGND
VL
SDOUT2
OSCLK2
OLRCK2
TDM_IN
SDOUT1
OSCLK1
OLRCK1
SRC_UNLOCK
RMCK
RST
THERMAL PAD
Pin Name
Pin #
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
-
Buffered MCLK (Output) - Buffered output of XTI clock. If a 20 kΩ pull-up resistor to VL is present on
this pin, the SRC MCLK source will be the PLL clock, otherwise it will be the ring oscillator.
TX Pin MUX Selection (Input) - Used to select the AES3-compatible receiver input for pass-through
to the TX pin.
Receiver MUX Selection (Input) - Used to select the active AES3-compatible receiver input.
Receiver Channel Status Block (Output) -Indicates the beginning of a received channel status
block. Will go high for one subframe during each Z preamble following the first detected Z preamble.
If no Z preamble is detected, output is indeterminate. See
Channel Status Data (Output) - Serial channel status data output from the AES3-compatible
receiver, clocked by the rising and falling edges of OLRCK2 in master mode. A 20 kΩ pull-up resistor
to VL must be present on this pin to put the part in Hardware Mode.
Receiver MUX Pass-through/User Data (Output) - If no 20 kΩ pull-up resistor is present on this pin
it will output a copy of the receiver mux input selected by the TX_SEL pin. If a 20 kΩ pull-up resistor
to VL is present on this pin, it will output serial User data from the AES3 receiver, clocked by the rising
and falling edges of OLRCK2 in master mode.
Voltage Regulator In (Input) - Regulator power supply input, nominally +3.3 V.
Digital Voltage Regulator Out (Output) - Digital core voltage regulator output. Should be connected
to digital ground through a 10 µF capacitor. Cannot be used as an external voltage source.
Digital & I/O Ground (Input) - Ground for the I/O and core logic. AGND and DGND should be con-
nected to a common ground area under the chip.
Logic Power (Input) - Input/Output power supply, typically +1.8 V, +2.5 V, +3.3 V, or +5.0 V.
Serial Audio Output 2 Data Port (Output) - Audio data serial output 2 pin.
Serial Audio Output 2 Bit Clock (Input/Output) - Serial bit clock for audio data on the SDOUT2 pin.
Serial Audio Output 2 Left/Right Clock (Input/Output) - Word rate clock for the audio data on the
SDOUT2 pin.
Serial Audio Output 1 TDM Input (Input) - Time Division Multiplexing serial audio data input.
Grounded when not used. See
Serial Audio Output 1 Data Port (Output) - Audio data serial output 1 pin. A 20 kΩ pull-up to VL
present on this pin will disable de-emphasis auto detect.
Serial Audio Output 1 Bit Clock (Input/Output) - Serial bit clock for audio data on the SDOUT1 pin.
Serial Audio Output 1 Left/Right Clock (Input/Output) - Word rate clock for the audio data on the
SDOUT1 pin.
SRC Unlock Indicator (Output) - Indicates when the SRC is unlocked. See
page 37
Recovered Master Clock (Output) - Recovered master clock from the PLL. Frequency is 128 x,
256 x, or 512 x Fs, where Fs is the sample rate of the incoming AES3-compatible data or ISCLK/64.
If a 20 kΩ pull-up to VL is present on this pin, the SDOUT2 MCLK source will be RMCK, otherwise it
will be the clock input through XTI-XTO.
Reset (Input) - When RST is low the CS8422 enters a low power mode and all internal states are
reset. On initial power up RST must be held low until the power supply is stable and all input clocks
are stable in frequency and phase.
Thermal Pad - Thermal relief pad. Should be connected to the ground plane for optimized heat dissi-
pation.
for more details.
“Time Division Multiplexing (TDM) Mode” on page 27
Pin Description
Figure 19 on page 36
“SRC Locking” on
for more detail.
for details.
CS8422
DS692PP1