IDT5T915PAGI IDT, Integrated Device Technology Inc, IDT5T915PAGI Datasheet - Page 5

• Manufacturer Part Number: IDT5T915PAGI
• Description: IC CLK BUFFER 1:5 DIFF 48-TSSOP
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Fanout Buffer (Distribution)r

Specifications of IDT5T915PAGI

• Number Of Circuits: 1
• Ratio - Input:output: 1:5
• Differential - Input:output: Yes/Yes
• Input: eHSTL, HSTL, LVPECL, LVTTL
• Output: eHSTL, HSTL, LVTTL
• Frequency - Max: 250MHz
• Voltage - Supply: 2.4 V ~ 2.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 48-TSSOP
• Frequency-max: 250MHz
• Number Of Outputs: 10
• Operating Supply Voltage (max): 2.6V
• Operating Temp Range: -40C to 85C
• Propagation Delay Time: 3.5ns
• Operating Supply Voltage (min): 2.4V
• Mounting: Surface Mount
• Pin Count: 48
• Operating Supply Voltage (typ): 2.5V
• Package Type: TSSOP
• Quiescent Current: 30mA
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 5T915PAGI

DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE FOR HSTL
NOTES:
1. See RECOMMENDED OPERATING RANGE table.
2. V
3. V
4. For single-ended operation, in differential mode, A/V
5. Voltage required to maintain a logic HIGH, single-ended operation in differential mode.
6. Voltage required to maintain a logic LOW, single-ended operation in differential mode.
7. Typical values are at V
8. The reference clock input is capable of HSTL, eHSTL, LVEPECL, 1.8V or 2.5V LVTTL operation independent of the device output. The correct input interface table should be
9. For differential mode (RxS = LOW), A and A/V
NOTES:
1. These power consumption characteristics are for all the valid input interfaces and cover the worst case input and output interface combinations.
2. The termination resistors are excluded from these measurements.
3. If the differential input interface is used, the true input is held LOW and the complementary input is held HIGH.
POWER SUPPLY CHARACTERISTICS FOR HSTL OUTPUTS
IDT5T915
2.5V DIFFERENTIAL 1:5 CLOCK BUFFER TERABUFFER
Input Characteristics
Output Characteristics
Symbol
only. The DC differential voltage must be maintained to guarantee retaining the existing HIGH or LOW input. The AC differential voltage must be achieved to guarantee switching
to a new state.
referenced.
Symbol
DIF
CM
I
I
V
I
V
V
V
V
I
DDQQ
I
DDDQ
I
TOTQ
V
V
V
V
DDQ
DDD
I
TOT
I
REF
DIF
IH
CM
OH
IL
OL
IK
IN
IH
IL
specifies the minimum input differential voltage (V
specifies the maximum allowable range of (V
Input HIGH Current
Input LOW Current
Clamp Diode Voltage
DC Input Voltage
DC Differential Voltage
DC Common Mode Input Voltage
DC Input HIGH
DC Input LOW
Single-Ended Reference Voltage
Output HIGH Voltage
Output LOW Voltage
Quiescent V
Quiescent V
Dynamic V
Current per Output
Dynamic V
Current per Output
Total Power V
Total Power V
DD
= 2.5V, V
Parameter
DD
DDQ
Parameter
DD
DDQ
DDQ
DD
Power Supply
(4,6,8)
Power Supply Current
Power Supply
(4,5,8)
Power Supply Current
Supply Current
Supply Current
(9)
(9)
DDQ
(2,8)
= 1.5V, +25°C ambient.
REF
(4,8)
(3,8)
TR
must be at the opposite rail.
REF
+ V
TR
is tied to the DC voltage V
- V
CP
) /2. Differential mode only.
CP
) required for switching where V
V
V
V
I
I
I
I
V
Outputs enabled, All outputs unloaded
V
Outputs enabled, All outputs unloaded
V
V
V
V
V
V
OH
OH
OL
OL
DD
DD
DD
DDQ
DDQ
DD
DD
DDQ
DDQ
DDQ
DDQ
= 8mA
= 100μA
= -8mA
= -100μA
= 2.6V
= 2.6V
= 2.4V, I
= Max., V
= Max., V
= Max., Reference Clock = LOW
= Max., Reference Clock = LOW
= 1.5V, F
= 1.5V, F
= 1.5V, F
= 1.5V, F
Test Conditions
Test Conditions
IN
DDQ
DDQ
REFERENCE CLOCK
REFERENCE CLOCK
REFERENCE CLOCK
REFERENCE CLOCK
= -18mA
REF
5
= Max., C
= Max., C
.
V
V
I
I
= V
= GND/V
(2)
TR
is the "true" input level and V
DDQ
L
L
= 0pF
= 0pF
= 100MHz, C
= 250MHz, C
= 100MHz, C
= 250MHz, C
/GND
DDQ
(3)
(3)
L
L
L
L
= 15pF
= 15pF
= 15pF
= 15pF
V
V
V
REF
DDQ
DDQ
Min.
- 0.3
680
0.2
—
—
—
—
—
—
—
+ 100
- 0.1
- 0.4
CP
INDUSTRIAL TEMPERATURE RANGE
is the "complement" input level. Differential mode
(1)
Typ.
Typ.
- 0.7
750
750
0.1
—
—
20
20
30
20
35
35
60
(7)
V
REF
- 1.2
+3.6
Max
Max
900
120
±5
±5
0.4
0.1
0.3
—
—
—
—
—
30
30
50
40
50
70
- 100
μA/MHz
μA/MHz
(1)
Unit
Unit
mV
mV
mV
mV
μA
mA
mA
mA
mA
V
V
V
V
V
V
V