KSZ8893MBL Micrel Inc, KSZ8893MBL Datasheet - Page 46

• Manufacturer Part Number: KSZ8893MBL
• Description: IC MANAGED SW 10/100 100-LFBGA
• Manufacturer: Micrel Inc

Specifications of KSZ8893MBL

• Controller Type: Ethernet Switch Controller
• Interface: MII, RMII, SNI
• Voltage - Supply: 3.1 V ~ 3.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 100-LFBGA
• Number Of Primary Switch Ports: 3
• Internal Memory Buffer Size: 32
• Operating Supply Voltage (typ): 3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Power Supply Type: Analog/Digital
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 3.5V
• Operating Supply Voltage (min): 3.1V
• Operating Temperature Classification: Commercial
• Data Rate: 100Mbps
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 576-1603 - EVAL KIT EXPERIMENTAL KSZ8893MQL
• Current - Supply: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 576-3090

For packets from regular ports (port 1 & port 2) to port 3, the port mask is used to tell the processor which port the
packets were received on, defined as follows:
No port mask values, other than the previous two defined ones, should be received in this direction in Special
Tagging Mode. The switch to processor egress rules are defined as follows:
IGMP Support
For Internet Group Management Protocol (IGMP) support in layer 2, the KSZ8893MQL/MBL provides two
components:
IGMP Snooping
The KSZ8893MQL/MBL traps IGMP packets and forwards them only to the processor (port 3). The IGMP packets
are identified as IP packets (either Ethernet IP packets, or IEEE 802.3 SNAP IP packets) with IP version = 0x4
and protocol version number = 0x2.
Multicast Address Insertion in the Static MAC Table
Once the multicast address is programmed in the Static MAC Table, the multicast session is trimmed to the
subscribed ports, instead of broadcasting to all ports.
To enable IGMP support, set register 5 bit [6] to ‘1’. Also, Special Tagging Mode needs to be enabled, so that the
processor knows which port the IGMP packet was received on. This is achieved by setting both register 11 bit [0]
and register 48 bit [2] to ‘1’.
IPv6 MLD Snooping
The KSZ8893MQL/MBL traps IPv6 Multicast Listener Discovery (MLD) packets and forwards them only to
processor (port 3). MLD snooping is controlled by register 5 bit 5 (MLD snooping enable) and register 5 bit 4
(MLD option).
With MLD snooping enabled, the KSZ8893MQL/MBL traps packets that meet all of the following conditions:
If the MLD option bit is set to “1”, the KSZ8893MQL/MBL traps packets with the following additional condition:
For MLD snooping, Special Tagging Mode also needs to be enabled, so that the processor knows which port the
MLD packet was received on. This is achieved by setting both register 11 bit [0] and register 48 bit [2] to ‘1’.
December 2007
“0001”, packet from port 1
“0010”, packet from port 2
Ingress Packets
Tagged with 0x8100 + TCI
Not tagged.
•
•
•
•
IPv6 multicast packets
Hop count limit = 1
IPv6 next header = 1 or 58 (or = 0 with hop-by-hop next header = 1 or 58)
IPv6 next header = 43, 44, 50, 51, or 60 (or = 0 with hop-by-hop next header = 43, 44, 50, 51, or
60)
Table 12. STPID Egress Rules (Switch Port 3 to Processor)
Egress Action to Tag Field
- Modify TPID to 0x810 + “port mask”, which indicates source port.
- No change to TCI if VID is not null
- Replace null VID with ingress port VID
- Recalculate CRC
- Insert TPID to 0x810 + “port mask”, which indicates source port
- Insert TCI with ingress port VID
- Recalculate CRC
46
M9999-121007-1.5