MAX9268GCM/V+ Maxim Integrated Products, MAX9268GCM/V+ Datasheet - Page 28

• Manufacturer Part Number: MAX9268GCM/V+
• Description: IC SERIALIZER GMSL LVDS 48TQFP
• Manufacturer: Maxim Integrated Products

Specifications of MAX9268GCM/V+

• Function: Deserializer
• Data Rate: 2.5Gbs
• Input Type: Serial
• Output Type: LVDS
• Voltage - Supply: 3.3V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 48-TQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Outputs: -
• Number Of Inputs: -

Gigabit Multimedia Serial Link Deserializer
with LVDS System Interface
Both the GMSL serializer and the MAX9268 have program-
mable device addresses. This allows multiple GMSL devic-
es along with I
channel. The serializer device address is stored in registers
0x00 of each device, while the deserializer device address
is stored in register 0x01 of each device. To change the
device address, first write to the device whose address
changes (register 0x00 of the GMSL serializer for serializer
device address change, or register 0x01 of the MAX9268
for deserializer device address change). Then write the
same address into the corresponding register on the other
device (register 0x00 of the MAX9268 for serializer device
address change, or register 0x01 of the GMSL serializer for
deserializer device address change).
ADD0 and ADD1 are 3-level inputs, which set the device
addresses stored in the MAX9268 (Table 2). Set the
desired device addresses by connecting ADD0/ADD1
through a pullup resistor to IOVDD, a pulldown resistor to
GND, or to high impedance. For digital control, use three-
state logic to drive the 3-level logic inputs.
ADD0/ADD1 set the device addresses in the MAX9268
only and not the GMSL serializer. Set the GMSL serial-
izer’s ADD0/ADD1 inputs to the same settings as the
MAX9268; alternatively, write to registers 0x00 and 0x01
of the GMSL serializer to reflect any changes made due
to the 3-level inputs.
Both I
provide a logic-high level. There are trade-offs between
power dissipation and speed, and a compromise made in
choosing pullup resistor values. Every device connected
to the bus introduces some capacitance even when the
device is not in operation. I
go from low to high (30% to 70%) for fast mode, which is
defined for data rates up to 400kbps (see the I
tions in the AC Electrical Characteristics section for details).
To meet the fast-mode rise-time requirement, choose the
pullup resistors such that rise time t
C
transition time becomes too slow. The MAX9268 supports
I
28
2
BUS
C/UART rates up to 1Mbps.
_____________________________________________________________________________________
3-Level Inputs for Default Device Address
2
< 300ns. The waveforms are not recognized if the
C/UART open-drain lines require pullup resistors to
Choosing I
Programming the Device Addresses
2
C peripherals to coexist on the same control
2
C/UART Pullup Resistors
2
C specifies 300ns rise times to
R
= 0.85 x R
2
C specifica-
PULLUP
x
AC-coupling isolates the receiver from DC voltages up
to the voltage rating of the capacitor. Four capacitors
(two at the serializer output and two at the deserializer
input) are needed for proper link operation and to provide
protection if either end of the cable is shorted to a high volt-
age. AC-coupling blocks low-frequency ground shifts and
low-frequency common-mode noise.
Voltage droop and the digital sum variation (DSV) of
transmitted symbols cause signal transitions to start from
different voltage levels. Because the transition time is finite,
starting the signal transition from different voltage levels
causes timing jitter. The time constant for an AC-coupled
link needs to be chosen to reduce droop and jitter to an
acceptable level. The RC network for an AC-coupled link
consists of the CML receiver termination resistor (R
the CML driver termination resistor (R
AC-coupling capacitors (C). The RC time constant for four
equal-value series capacitors is (C x (R
and R
ance (usually 100I). This leaves the capacitor selection
to change the system time constant. Use at least 0.2FF
high-frequency surface-mount ceramic capacitors, with
sufficient voltage rating to withstand a short to battery, to
pass the lower speed reverse control-channel signal. Use
capacitors with a case size less than 3.2mm x 1.6mm to
have lower parasitic effects to the high-speed signal.
The MAX9268 uses a 3.0V to 3.6V V
single-ended inputs and outputs on the MAX9268 derive
power from a 1.7V to 3.6V V
IOVDD. Proper voltage-supply bypassing is essential for
high-frequency circuit stability.
Interconnect for CML typically has a differential impedance
of 100I. Use cables and connectors that have matched
differential impedance to minimize any impedance dis-
continuities. Twisted-pair and shielded twisted-pair cables
tend to generate less EMI due to magnetic-field canceling
effects. Balanced cables pick up noise as common mode
rejected by the CML receiver. Table 11 lists the suggested
cables and connectors used in the GMSL link.
TR
are required to match the transmission line imped-
Power-Supply Circuits and Bypassing
Selection of AC-Coupling Capacitors
Cables and Connectors
IOVDD
AVDD
, which scales with
TD
TD
), and the series
AC-Coupling
and V
+ R
TR
DVDD
))/4. R
TR
. All
TD
),