CS5396-KS Cirrus Logic Inc, CS5396-KS Datasheet - Page 15

• Manufacturer Part Number: CS5396-KS
• Description: ADC Dual Delta-Sigma 96KSPS 24-Bit Serial 28-Pin SOIC
• Manufacturer: Cirrus Logic Inc

Specifications of CS5396-KS

• Package: 28SOIC
• Resolution: 24 Bit
• Sampling Rate: 96 KSPS
• Architecture: Delta-Sigma
• Number Of Analog Inputs: 2
• Digital Interface Type: Serial (SPI)
• Input Type: Voltage
• Sample And Hold: Yes
• Polarity Of Input Voltage: Bipolar

Master Clock - Control Port Mode
The master clock is the clock source for the delta-
sigma modulator sampling (MCLKA) and digital
filters (MCLKD). The required MCLKA/D fre-
quency is determined by the desired Fs and the cho-
sen Oversampling Mode. Table 2 shows some
common master clock frequencies.
64 vs. 128 Oversampling Modes
The CS5396/97 can operate in a 64 Oversampling
Mode with a 256 master clock (MCLKA/D) at a
maximum sample rate of 100 kHz. The device can
also operate in a 128 Oversampling Mode with a
512 master clock (MCLKA/D) where the maxi-
mum Fs is 50 kHz. Notice that the required master
clock is 24.576 MHz for Fs equal to either 48 kHz
in the 128 Oversampling Mode or 96 kHz in the
64 Oversampling Mode. The sampling mode is
set via the control register which alters the decima-
tion ratio of the digital filter. The 64 Oversam-
pling Mode is the default mode. Table 2 shows
some common clock frequencies for both modes.
Refer to Appendix A for additional discussion of
64 vs. 128 Oversampling Modes.
Serial Data Interface - Control Port Mode
The CS5396/97 supports two serial data formats
which are selected via the control register. The dig-
ital output format determines the relationship be-
tween the serial data, left/right clock and serial
DS229PP2
LRCK
(kHz)
44.1
44.1
88.2
32
48
32
48
64
96
Table 2. Common Clock Frequencies
sampling
Over-
128
128
128
64
64
64
64
64
64
MCLKA/D
11.2896
22.5792
22.5792
12.288
16.384
24.576
16.384
24.576
(MHz)
8.192
5.6448
5.6448
SCLK
(MHz)
2.048
2.822
3.072
4.096
6.144
4.096
6.144
clock. Figures 4 - 7 detail the interface formats.
The serial data interface is accomplished via the se-
rial data outputs; SDATA1 and SDATA2, serial
data clock, SCLK, and the left/right clock, LRCK.
The serial nature of the output data results in the left
and right data words being read at different times.
However, the samples within an LRCK cycle repre-
sent simultaneously sampled analog inputs.
Serial Data - Control Port Mode
The serial data block is presented in 2’s-comple-
ment format with the MSB-first. The data is clocked
from SDATA1 and SDATA2 by the serial clock
and the channel is determined by the Left/Right
clock. The full precision 24 bit data is available on
SDATA1 and the output from the low group delay
is available on SDATA2.
The serial data can be followed by 8 Peak Signal
Level, PSL, bits as shown in Figures 4 - 7 if the
PKEN bit is set. Refer to the Dual Audio Output
section of this data sheet for further discussion of
SDATA1 and SDATA2 options.
Serial Clock - Control Port Mode
The serial clock shifts the digitized audio data from
the internal data registers via SDATA1 and
SDATA2. SCLK is an output in Master Mode
where internal dividers will divide the master clock
by 4 to generate a serial clock which is 64 Fs in
the 64 Oversampling Mode. In the 128 Over-
sampling Mode, internal dividers will divide
MCLKA/D by 4 to generate a SCLK which is 128
Fs. In Slave Mode, SCLK is an input with a serial
clock typically between 48 and 128 Fs. It is rec-
ommended that SCLK be equal to 64 in the 64
Oversampling Mode and equal to 128 in the 128
Oversampling Mode to avoid possible system per-
formance degradation due to interference effects.
Left/Right Clock -Control Port Mode
The Left/Right clock, LRCK, determines which
channel, left or right, is to be output on SDATA1
CS5396 CS5397
15