SI3050-KT Silicon Laboratories Inc, SI3050-KT Datasheet - Page 61

• Manufacturer Part Number: SI3050-KT
• Description: IC VOICE DAA GCI/PCM/SPI 20TSSOP
• Manufacturer: Silicon Laboratories Inc
• Type: Chipsetr

Specifications of SI3050-KT

• Package / Case: 20-TSSOP
• Function: Data Access Arrangement (DAA)
• Interface: PCM, Serial, SPI
• Number Of Circuits: 1
• Voltage - Supply: 3 V ~ 3.6 V
• Current - Supply: 8.5mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Includes: Line Voltage Monitor, Loop Current Monitor, Overload Detection, Parallel Handset Detection, Polarity Reversal Detection, TIP and
• Product: Modem Chip
• Supply Voltage (min): 3 V
• Supply Current: 8.5 mA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Power (watts): -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Contains lead / RoHS non-compliant

Register 4. Interrupt Source
Reset settings = 0000_0000
Name
Type
Bit
Bit
7
6
5
4
3
2
LCSOI
RDTI
Name
ROVI
DODI
R/W
RDTI
FDTI
BTDI
D7
ROVI
R/W
D6
Ring Detect Interrupt.
0 = A ring signal is not occurring.
1 = A ring signal is detected. If the RDTM bit (Register 3) and INTE bit (Register 2) are set, a
hardware interrupt occurs on the AOUT/INT pin. This bit must be written to a 0 to be cleared.
The RDI bit (Register 2) determines if this bit is set only at the beginning of a ring pulse, or at
the both the beginning and end of a ring pulse. This bit should be cleared after clearing the
PDL bit (Register 6) as powering up the line-side device can cause this interrupt to be trig-
gered.
Receive Overload Interrupt.
0 = An excessive input level on the receive pin is not occurring.
1 = An excessive input level on the receive pin is detected. If the ROVM bit (Register 3) and
INTE bit (Register 2) are set, a hardware interrupt occurs on the AOUT/INT pin. This bit must
be written to 0 to clear it. This bit is identical in function to the ROV bit (Register 17) and clear-
ing this bit also clears the ROV bit.
Frame Detect Interrupt.
0 = Frame detect is established on the ISOcap link.
1 = This bit is set when the ISOcap link does not have frame lock. If the FDTM bit (Register 3)
and INTE bit (Register 2) are set, a hardware interrupt occurs on the AOUT/INT pin. When
set, this bit must be written to 0 to be cleared.
Billing Tone Detect Interrupt.
0 = A billing tone has not occurred.
1 = A billing tone has been detected. If the BTDM bit (Register 3) and INTE bit (Register 2)
are set, a hardware interrupt occurs on the AOUT/INT pin. This bit must be written to 0 to
clear it.
Drop Out Detect Interrupt.
0 = The line-side power supply has not collapsed.
1 = The line-side power supply has collapsed. (The DOD bit in Register 19 has fired.) If the
DODM bit (Register 3) and INTE bit (Register 2) are set, a hardware interrupt occurs on the
AOUT/INT pin. This bit must be written to 0 to be cleared. This bit should be cleared after
clearing the PDL bit (Register 6) as powering up the line-side device can cause this interrupt
to be triggered.
Loop Current Sense Overload Interrupt.
0 = The LCS bits have not reached max (all ones).
1 = The LCS bits have reached max value. If the LCSOM bit (Register 3) and the INTE bit are
set, a hardware interrupt occurs on the AOUT/INT pin. This bit must be written to 0 to clear it.
Note: LCSOI does not necessarily imply that an overcurrent situation has occurred. An overcurrent
situation in the DAA is determined by the status of the OPD bit (Register 19). After the LCSOI
interrupt fires, the OPD bit should be checked to determine if an overcurrent situation exists.
FDTI
R/W
D5
BTDI
R/W
D4
DODI LCSOI TGDI
R/W
D3
R/W
D2
Rev. 1.0
R/W
D1
Function
POLI
R/W
D0
Si3050
61