ATtiny861 Atmel Corporation, ATtiny861 Datasheet - Page 113

• Manufacturer Part Number: ATtiny861
• Manufacturer: Atmel Corporation

Specifications of ATtiny861

• Flash (kbytes): 8 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

2588E–AVR–08/10
Table 12-10
are set to Phase and Frequency Correct PWM Mode.
Table 12-10. Compare Output Mode, Phase and Frequency Correct PWM Mode
Table 12-11
are set to single-slope PWM6 Mode. In the PWM6 Mode the same Waveform Output (OCW1A)
is used for generating all waveforms and the Output Compare values OC1A and OC1A are con-
nected on thw all OC1x and OC1x pins as described below.
Table 12-11. Compare Output Mode, Single-Slope PWM6 Mode
Table 12-12
are set to dual-slope PWM6 Mode.I
Table 12-12. Compare Output Mode, Dual-Slope PWM6 Mode
Bits COM1A1 and COM1A0 are shadowed in TCCR1C. Writing to bits COM1A1 and COM1A0
will also change bits COM1A1S and COM1A0S in TCCR1C. Similary, changes written to bits
COM1A1S and COM1A0S in TCCR1C will show here. See
Register C” on page
COM1A1:0
COM1A1:0
COM1A1:0
00
01
10
11
00
01
10
11
00
01
10
11
shows the COM1A1:0 bit functionality when the PWM1A, WGM10 and WGM11 bits
shows the COM1A1:0 bit functionality when the PWM1A, WGM10 and WGM11 bits
shows the COM1A1:0 bit functionality when the PWM1A, WGM10 and WGM11 bits
OCW1A Behaviour
Normal port operation.
Cleared on Compare Match when up-counting.
Set on Compare Match when down-counting.
Cleared on Compare Match when up-counting.
Set on Compare Match when down-counting.
Set on Compare Match when up-counting.
Cleared on Compare Match when down-counting.
OCW1A Behaviour
Normal port operation.
Cleared on Compare Match.
Set when TCNT1 = 0x000.
Cleared on Compare Match.
Set when TCNT1 = 0x000.
Set on Compare Match.
Cleared when TCNT1 = 0x000.
OCW1A Behaviour
Normal port operation.
Cleared on Compare Match when up-counting.
Set on Compare Match when down-counting.
Cleared on Compare Match when up-counting.
Set on Compare Match when down-counting.
Set on Compare Match when up-counting.
Cleared on Compare Match when down-counting.
117.
“TCCR1C – Timer/Counter1 Control
OC1A Pin
Disconnected
OC1x Pin
Disconnected
OC1x Pin
Disconnected
Connected
Connected
Connected
OC1A
OC1A
OC1A
OC1A
OC1A
OC1A
OC1A Pin
Disconnected
Connected
Disconnected
Disconnected
OC1x Pin
Disconnected
OC1A
OC1A
OC1A
OC1x Pin
Disconnected
OC1A
OC1A
OC1A
113