ATtiny861 Atmel Corporation, ATtiny861 Datasheet - Page 66

• Manufacturer Part Number: ATtiny861
• Manufacturer: Atmel Corporation

Specifications of ATtiny861

• Flash (kbytes): 8 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

10.2.2
66
ATtiny261/461/861
Alternate Functions of Port B
The Port B pins with alternate function are shown in
Table 10-6.
• Port B, Bit 7 – RESET/ dW/ ADC10/ PCINT15
• RESET, Reset pin: When the RSTDISBL Fuse is programmed, this pin functions as a normal
• If PB7 is used as a reset pin, DDB7, PORTB7 and PINB7 will all read 0.
• dW: When the debugWIRE Enable (DWEN) Fuse is programmed and Lock bits are
I/O pin, and the part will have to rely on Power-on Reset and Brown-out Reset as its reset
sources. When the RSTDISBL Fuse is unprogrammed, the reset circuitry is connected to the
pin, and the pin can not be used as an I/O pin.
unprogrammed, the RESET port pin is configured as a wire-AND (open-drain) bi-directional
I/O pin with pull-up enabled and becomes the communication gateway between target and
emulator.
Port Pin
PB7
PB6
PB5
PB4
PB3
PB2
PB1
PB0
Port B Pins Alternate Functions
Alternate Function
RESET: Reset pin
dW:
ADC10: ADC Input Channel 10
PCINT15:Pin Change Interrupt 0, Source 15
ADC9:
T0:
INT0:
PCINT14:Pin Change Interrupt 0, Source 14
XTAL2: Crystal Oscillator Output
CLKO: System Clock Output
OC1D: Timer/Counter1 Compare Match D Output
ADC8:
PCINT13:Pin Change Interrupt 0, Source 13
XTAL1: Crystal Oscillator Input
CLKI:
OC1D: Inverted Timer/Counter1 Compare Match D Output
ADC7:
PCINT12:Pin Change Interrupt 0, Source 12
OC1B: Timer/Counter1 Compare Match B Output
PCINT11:Pin Change Interrupt 0, Source 11
USCK: USI Clock (Three Wire Mode)
SCL :
OC1B: Inverted Timer/Counter1 Compare Match B Output
PCINT10:Pin Change Interrupt 0, Source 10
DO:
OC1A: Timer/Counter1 Compare Match A Output
PCINT9: Pin Change Interrupt 1, Source 9
DI:
SDA:
OC1A: Inverted Timer/Counter1 Compare Match A Output
PCINT8: Pin Change Interrupt 1, Source 8
debugWire I/O
ADC Input Channel 9
Timer/Counter0 Clock Source
External Interrupt 0 Input
ADC Input Channel 8
External Clock Input
ADC Input Channel 7
USI Clock (Two Wire Mode)
USI Data Output (Three Wire Mode)
USI Data Input (Three Wire Mode)
USI Data Input (Two Wire Mode)
Table
10-6.
2588E–AVR–08/10