EVX8AQ160TPY ETC-unknow, EVX8AQ160TPY Datasheet - Page 11

no-image

EVX8AQ160TPY

Manufacturer Part Number
EVX8AQ160TPY
Description
Adc Quad 1.25gsps 8-bit Lvds 380-pin Ebga
Manufacturer
ETC-unknow
Datasheet
Table 5-1.
Notes:
5.1
Table 5-2.
e2v semiconductors SAS 2009
Parameter
INLrms
Integral nonlinearity
Integral nonlinearity
Parameter
AC Analog Inputs
Full power input bandwidth
Full setting (BW = 11 in register 0x01)
Nominal setting (BW = 10 in register 0x01)
Reduced setting (BW = 01 in register 0x01)
Min setting (BW = 00 in register 0x01, default
mode)
Gain flatness (over any 500 MHz in full bandwidth
setting, BW = 11 in register 0x01)
Input voltage standing wave ratio
Crosstalk (Fin = 620 MHz)
1. The input common mode voltage is delivered via the CMIRefAB and CMIRefCD signals for channels A and B, and C and D
2. The input resistance can be trimmed via register at address 0x13 to reach the 100Ω value.
3. A minimum noise margin of 0.05 × V
4. Parameters specified for characterization purpose only, not valid at chip level specification.
5. Takes in account 200 mV voltage drop in both supply lines.
6. Iolc and Iohc values are source/sink currents in worst case conditions reflected in the name of the IO cell.
7. Leakage values related to ESD protection scheme and must be checked against leakage current observed with this process.
8. Internal 75 kΩ pull up.
9. Differential output buffers impedance = 100Ω differential.
10. Offset and Gain central values can be set to 0 mV and 1 respectively using the gain and offset adjustments provided in the
11. Values obtained without calibration. With calibration, |INL| values can be lowered to ±0.25 LSB typ (± 0.5 LSB max).
AC Electrical Characteristics
respectively. The minimum load allowed on these signals is 2.5 kΩ (optimal load = 5 kΩ to 10 kΩ).
Vihc.
SPI.
Electrical Characteristics (Continued)
AC Electrical Characteristics
Unless otherwise specified:
• V
• –1 dBFS analog input (full scale Input: V
• Clock input differentially driven; analog input differentially driven
• Default mode: four-channel mode ON, binary output data format, digital interface ON, 1:2 DMUX ON,
standby mode OFF minimum bandwidth
CC
= 3.3V, V
CCD
= 1.8V, V
Symbol
INLrms
INL+
INL-
CC
is taken for Schmitt trigger input threshold switching levels compared to Vilc and
CCO
Symbol
FPBW
GF
VSWR
= 1.8V
Level
Test
1,4
1,4
1,4
IN
Level
Test
1,4
– V
4
4
4
Min
–0.9
INN
= 500 mVpp)
55
Min
1.5
1.3
400
300
Typ
0.11
–0.27
0.27
Typ
2
1.5
600
500
62
Max
0.4
0.9
Max
1
1.6
0846G–BDC–11/09
Unit
GHz
GHz
MHz
MHz
dB
dB
EV8AQ160
Unit
LSB
LSB
LSB
Notes
(1)
(2)
Notes
(11)
(11)
(11)
11

Related parts for EVX8AQ160TPY