M25PE20-VMN6TP NUMONYX, M25PE20-VMN6TP Datasheet - Page 32

• Manufacturer Part Number: M25PE20-VMN6TP
• Description: IC FLASH 2MBIT 75MHZ 8SOIC
• Manufacturer: NUMONYX
• Series: Forté™r

Specifications of M25PE20-VMN6TP

• Format - Memory: FLASH
• Memory Type: FLASH
• Memory Size: 2M (256K x 8)
• Speed: 75MHz
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Cell Type: NOR
• Density: 2Mb
• Access Time (max): 8ns
• Interface Type: Serial (SPI)
• Boot Type: Not Required
• Address Bus: 1b
• Operating Supply Voltage (typ): 3.3V
• Operating Temp Range: -40C to 85C
• Package Type: SOIC N
• Sync/async: Synchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8b
• Number Of Words: 256K
• Supply Current: 8mA
• Mounting: Surface Mount
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: M25PE20-VMN6TPTR

Instructions
6.7
32/64
Read Data Bytes at Higher Speed (FAST_READ)
The device is first selected by driving Chip Select (S) Low. The instruction code for the Read
Data Bytes at Higher Speed (FAST_READ) instruction is followed by a 3-byte address (A23-
A0) and a dummy byte, each bit being latched-in during the rising edge of Serial Clock (C).
Then the memory contents, at that address, is shifted out on Serial Data output (Q), each bit
being shifted out, at a maximum frequency f
The instruction sequence is shown in
The first byte addressed can be at any location. The address is automatically incremented
to the next higher address after each byte of data is shifted out. The whole memory can,
therefore, be read with a single Read Data Bytes at Higher Speed (FAST_READ)
instruction. When the highest address is reached, the address counter rolls over to
000000h, allowing the read sequence to be continued indefinitely.
The Read Data Bytes at Higher Speed (FAST_READ) instruction is terminated by driving
Chip Select (S) High. Chip Select (S) can be driven High at any time during data output. Any
Read Data Bytes at Higher Speed (FAST_READ) instruction, while an Erase, Program or
Write cycle is in progress, is rejected without having any effects on the cycle that is in
progress.
Figure 14. Read Data Bytes at Higher Speed (FAST_READ) instruction sequence
1. Address bits A23 to A18 are ‘Don’t care’ in the M25PE20. Address bits A23 to A17 are ‘Don’t care’ in the
S
C
D
Q
S
C
D
Q
M25PE10.
and data-out sequence
0
7
32 33 34
1
6
High Impedance
2
5
Dummy byte
Instruction
3
4
35
4
3
36 37 38 39 40 41 42 43 44 45 46
5
2
6
1
7
0
MSB
23
8
7
Figure
22 21
9 10
6
24-bit address
DATA OUT 1
5
C
14.
, during the falling edge of Serial Clock (C).
4
3
28 29 30 31
3
2
2
1
1
0
0
47
MSB
7
6
DATA OUT 2
5
4
M25PE20, M25PE10
3
2
1
0
MSB
7
AI04006