CS5460A-BSZ Cirrus Logic Inc, CS5460A-BSZ Datasheet - Page 14

• Manufacturer Part Number: CS5460A-BSZ
• Description: IC ENERGY METERING 1PHASE 24SSOP
• Manufacturer: Cirrus Logic Inc

Specifications of CS5460A-BSZ

• Package / Case: 24-SSOP
• Input Impedance: 30 KOhm
• Measurement Error: 0.1%
• Voltage - I/o High: 0.8V
• Voltage - I/o Low: 0.2V
• Current - Supply: 2.9mA
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Meter Type: Single Phase
• Output Voltage Range: 2.4 V to 2.6 V
• Output Current: 1 uA
• Input Voltage Range: 2.4 V to 2.6 V
• Input Current: 25 nA
• Power Dissipation: 500 mW
• Operating Temperature Range: - 40 C to + 85 C
• Mounting Style: SMD/SMT
• Ic Function: Single Phase Bi-directional Power / Energy IC
• Brief Features: On-Chip Functions, AC Or DC System Calibration, Power Supply Monitor
• Supply Voltage Range: 3.3V To 5V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: CDB5460AU - EVALUATION BOARD FOR CS5460A
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 598-1094-5

full-scale. Note that the 24-bit signed output words
are expressed in two’s complement format. The
24-bit data words in the CS5460A output registers
represent values between 0 and 1 (for unsigned
output registers) or between -1 and +1 (for signed
output registers). A register value of 1 represents
the maximum possible value. Note that a value of
1.0 is never actually obtained in the registers of the
CS5460A. As an illustration, in any of the signed
output registers, the maximum register value is
[(2^23 - 1) / (2^23)] = 0.999999880791. After each
A/D conversion, the CRDY bit will be asserted in
the Status Register, and the INT pin will also be-
come active if the CRDY bit is unmasked (in the
Mask Register). The assertion of the CRDY bit in-
dicates that new instantaneous 24-bit voltage and
current samples have been collected, and these
two samples have also been multiplied together to
provide a corresponding instantaneous 24-bit pow-
er sample.
Table 1 conveys the typical relationship between
the differential input voltage (across the “+” and “-”
input pins of the voltage channel input) and the cor-
responding output code in the Instantaneous Volt-
age Register. Note that this table is applicable for
the current channel if the current channel’s PGA
gain is set for the “10x” gain mode.
14
-0.5
-1.0
-1.5
-2.0
-2.5
0.5
0.0
Figure 4. Voltage Input Filter Characteristics
0
200
400
600
Frequency (Hertz)
800
1000 1200 1400
1600 1800 2000
The V
dated every N conversions (which is known as 1
“computation cycle”), where N is the value in the
Cycle Count Register. At the end of each computa-
tion cycle, the DRDY bit in the Mask Register will
be set, and the INT pin will become active if the
DRDY bit is unmasked.
DRDY is set only after each computation cycle has
completed, whereas the CRDY bit is asserted after
each individual A/D conversion. Bits asserted by
the CS5460A must be cleared before being assert-
ed again. If the Cycle Count Register value (N) is
set to 1, all output calculations are instantaneous,
and DRDY will indicate when instantaneous calcu-
lations are finished, just like the CRDY bit. For the
RMS results to be valid, the Cycle-Count Register
must be set to a value greater than 10.
The computation cycle frequency is derived from
the
(MCLK/K)/(1024*N). Under default conditions, with
-44.7 nV to -14.9 nV
-14.9 nV to 14.9 nV
Input Voltage (DC)
14.9 nV to 44.7 nV
Table 1. Differential Input Voltage vs. Output Code
-0.5
-1.5
-2.5
0.5
-1
-2
0
0
Figure 5. Current Input Filter Characteristics
+250 mV
-250 mV
master
RMS
200
, I
RMS
400
clock,
, and energy calculations are up-
600
(hexidecimal)
Output Code
800
FFFFFF
7FFFFF
Frequency (Hertz)
000001
000000
800000
and
1000 1200 1400 1600 1800 2000
has
Output Code
CS5460A
a
(decimal)
-8388608
8388607
value
-1
1
0
DS487F4
of