KSZ8993MI Micrel Inc, KSZ8993MI Datasheet - Page 32

• Manufacturer Part Number: KSZ8993MI
• Description: IC SWITCH 10/100 W/TXRX 128PQFP
• Manufacturer: Micrel Inc

Specifications of KSZ8993MI

• Applications: *
• Mounting Type: Surface Mount
• Package / Case: 128-MQFP, 128-PQFP
• Number Of Primary Switch Ports: 3
• Internal Memory Buffer Size: 32
• Operating Supply Voltage (typ): 1.8/2.5/3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Phy/transceiver Interface: MII/SNI
• Power Supply Type: Analog/Digital
• Package Type: PQFP
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Pin Count: 128
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 1.89/3.465V
• Operating Supply Voltage (min): 1.71/3.135V
• Power Dissipation: 800mW
• Supply Current: 0.1/0.19A
• Operating Temperature Classification: Industrial
• Data Rate: 100Mbps
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 576-2124; KSZ8993MI

The MII interface operates in either PHY mode or MAC mode. The interface is a nibble wide data interfaces and
therefore run at ¼ the network bit rate (not encoded). Additional signals on the transmit side indicate when data is
valid or when an error occurs during transmission. Likewise, the receive side has indicators that convey when the
data is valid and without physical layer errors. For half duplex operation there is a signal that indicates a collision
has occurred during transmission.
Note that the signal MRXER is not provided on the interface for PHY mode operation and the signal MTXER is
not provided on the interface for MAC mode operation. Normally MRXER would indicate a receive error coming
from the physical layer device. MTXER would indicate a transmit error from the MAC device. These signals are
not appropriate for this configuration. For PHY mode operation, if the device interfacing with the KSZ8993M has
an MRXER pin, it should be tied low. For MAC mode operation, if the device interfacing with the KSZ8993M has
an MTXER pin, it should be tied low.
SNI (7-Wire) Operation
The serial network interface (SNI) or 7-wire is compatible with some controllers used for network layer protocol
processing. In SNI mode, the KSZ8993M acts like a PHY and the external controller functions as the MAC. The
KSZ8993M can interface directly with external controllers using the 7-wire interface. These signals are divided
into two groups, one for transmission and the other for reception. The signals involved are described in the
following table.
The SNI interface is a bit wide data interface and therefore runs at the network bit rate (not encoded). An
additional signal on the transmit side indicates when data is valid. Similarly, the receive side has an indicator that
conveys when the data is valid.
For half duplex operation, the KSZ8993M’s SCOL signal is used to indicate that a collision has occurred during
transmission.
MII Management Interface (MIIM)
The KSZ8993M supports the IEEE 802.3 MII Management Interface, also known as the Management Data
Input/Output (MDIO) Interface. This interface allows upper-layer devices to monitor and control the states of the
KSZ8993M. An external device with MDC/MDIO capability can be used to read the PHY status or configure the
PHY settings. Further details on the MIIM interface can be found in section 22.2.4.5 of the IEEE 802.3
specification.
Micrel, Inc.
October 2008
Pin Descriptions
Transmit enable
Serial transmit data
Transmit clock
Collision detection
Carrier sense
Serial receive data
Receive clock
Table 4. SNI Signals
External MAC
Controller Signals
TXEN
TXD
TXC
COL
CRS
RXD
RXC
32
SCOL
KSZ8993M
PHY Signals
SMTXEN
SMTXD[0]
SMTXC
SMRXDV
SMRXD[0]
SMRXC
M9999-020606
KSZ8993M/ML