ATTINY26-16MU Atmel, ATTINY26-16MU Datasheet - Page 127
![IC AVR MCU 2K 16MHZ IND 32-QFN](/photos/12/13/121313/attiny26-16mu_sml.jpg)
ATTINY26-16MU
Manufacturer Part Number
ATTINY26-16MU
Description
IC AVR MCU 2K 16MHZ IND 32-QFN
Manufacturer
Atmel
Series
AVR® ATtinyr
Specifications of ATTINY26-16MU
Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
USI
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
16
Program Memory Size
2KB (1K x 16)
Program Memory Type
FLASH
Eeprom Size
128 x 8
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 11x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
Processor Series
ATTINY2x
Core
AVR8
Data Bus Width
8 bit
Data Ram Size
128 B
Interface Type
2-Wire, ISP, SM-Bus, SPI, UART, USI
Maximum Clock Frequency
16 MHz
Number Of Programmable I/os
16
Number Of Timers
2
Operating Supply Voltage
4.5 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
EWAVR, EWAVR-BL
Development Tools By Supplier
ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 11 Channel
Package
32MLF EP
Device Core
AVR
Family Name
ATtiny
Maximum Speed
16 MHz
For Use With
ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK505 - ADAPTER KIT FOR 14PIN AVR MCU
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATTINY26-16MU
Manufacturer:
ATMEL
Quantity:
7 119
Notes:
1477K–AVR–08/10
T
Symbol
I
V
I
t
A
CC
ACLK
ACID
ACIO
= -40°C to +85°C, V
1. Typical values at 25°C.
2. “Max” means the highest value where the pin is guaranteed to be read as low.
3. “Min” means the lowest value where the pin is guaranteed to be read as high.
4. Although each I/O port can sink more than the test conditions (20mA at Vcc = 5V, 10 mA at Vcc = 3V) under steady state
5. Although each I/O port can source more than the test conditions (20 mA at V
6. Minimum V
conditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 400 mA.
2] The sum of all IOL, for port A0 - A7, should not exceed 300 mA.
3] The sum of all IOL, for ports B0 - B7 should not exceed 300 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 400 mA.
2] The sum of all IOH, for port A0 - A7, should not exceed 300 mA.
3] The sum of all IOH, for ports B0 - B7 should not exceed 300 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
Parameter
Power Supply Current
Power-down mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
CC
CC
for Power-down is 2.5V.
= 2.7V to 5.5V (unless otherwise noted) (Continued)
(6)
(ATtiny26L)
Active 4 MHz, V
(ATtiny26L)
Active 8 MHz, V
(ATtiny26)
Idle 1 MHz, V
WDT disabled, V
V
V
V
Condition
Active 1 MHz, V
(ATtiny26L)
Idle 4 MHz, V
(ATtiny26L)
Idle 8 MHz, V
(ATtiny26)
WDT enabled, V
V
V
V
in
in
CC
CC
CC
CC
= V
= V
= 5V
= 5V
= 2.7V
= 4.0V
CC
CC
/2
/2
CC
CC
CC
CC
CC
CC
CC
= 3V
= 3V
= 5V
CC
= 3V
= 3V
= 5V
= 3V
= 3V
Min.
-50
CC
Typ.
= 5V, 10 mA at V
0.70
0.18
0.75
<10
750
500
2.5
3.5
7.5
0.3
8
(1)
Max.
CC
15
15
40
50
6
2
7
3
= 3V) under steady state
Units
mA
mA
mA
mA
mV
mA
mA
µA
µA
nA
ns
127