AT90PWM3B-16SU Atmel, AT90PWM3B-16SU Datasheet - Page 121

• Manufacturer Part Number: AT90PWM3B-16SU
• Description: IC MCU AVR RISC 8K FLASH 32-SOIC
• Manufacturer: Atmel
• Series: AVR® 90PWM Lightingr

Specifications of AT90PWM3B-16SU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 27
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 32-SOIC (7.5mm Width)
• Processor Series: AT90PWMx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI/USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 27
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRFBKIT, ATAVRISP2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• On-chip Dac: 1-chx10-bit
• Controller Family/series: AVR PWM
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-SOIC - STK600 SOCKET/ADAPTER FOR SOIC770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRMC200 - KIT EVAL FOR AT90PWM3 ASYNCATAVRFBKIT - KIT DEMO BALLAST FOR AT90PWM2ATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK520 - ADAPTER KIT FOR 90PWM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

15.9
4317J–AVR–08/10
Timer/Counter Timing Diagrams
The extreme values for the OCRnx Register represents special cases when generating a PWM
waveform output in the phase correct PWM mode. If the OCRnx is set equal to BOTTOM the
output will be continuously low and if set equal to TOP the output will be set to high for non-
inverted PWM mode. For inverted PWM the output will have the opposite logic values. If OCR1A
is used to define the TOP value (WGM13:0 = 9) and COM1A1:0 = 1, the OC1A output will toggle
with a 50% duty cycle.
The Timer/Counter is a synchronous design and the timer clock (clk
clock enable signal in the following figures. The figures include information on when Interrupt
Flags are set, and when the OCRnx Register is updated with the OCRnx buffer value (only for
modes utilizing double buffering).
Figure 15-10. Timer/Counter Timing Diagram, Setting of OCFnx, no Prescaling
Figure 15-11
Figure 15-11. Timer/Counter Timing Diagram, Setting of OCFnx, with Prescaler (f
Figure 15-12
frequency correct PWM mode the OCRnx Register is updated at BOTTOM. The timing diagrams
will be the same, but TOP should be replaced by BOTTOM, TOP-1 by BOTTOM+1 and so on.
The same renaming applies for modes that set the TOVn Flag at BOTTOM.
TCNTn
OCRnx
OCFnx
TCNTn
OCRnx
(clk
OCFnx
(clk
clk
clk
clk
clk
I/O
I/O
I/O
Tn
I/O
Tn
/1)
/8)
shows the same timing data, but with the prescaler enabled.
shows the count sequence close to TOP in various modes. When using phase and
OCRnx - 1
OCRnx - 1
Figure 15-10
OCRnx
OCRnx
OCRnx Value
OCRnx Value
shows a timing diagram for the setting of OCFnx.
AT90PWM2/3/2B/3B
OCRnx + 1
OCRnx + 1
Tn
) is therefore shown as a
OCRnx + 2
OCRnx + 2
clk_I/O
/8)
121