PIC18F8410-I/PT Microchip Technology, PIC18F8410-I/PT Datasheet - Page 244

• Manufacturer Part Number: PIC18F8410-I/PT
• Description: IC PIC MCU FLASH 8KX16 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F8410-I/PT

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 70
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 70
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• No. Of Timers: 5
• Interface: I2C, SPI, USART
• Embedded Interface Type: I2C, SPI, USART
• Rohs Compliant: Yes
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: SPI, I2C, EUSART, AUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 4
• Operating Supply Voltage: 4.2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT80PT3 - SOCKET TRAN ICE 80MQFP/TQFPAC164320 - MODULE SKT MPLAB PM3 80TQFPAC174011 - MODULE SKT PROMATEII 80TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18F6310/6410/8310/8410
18.3.2
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTA2<5>), or the Continuous Receive
Enable bit, CREN (RCSTA2<4>). Data is sampled on
the RX2 pin on the falling edge of the clock.
If enable bit SREN is set, only a single word is received.
If enable bit CREN is set, the reception is continuous
until CREN is cleared. If both bits are set, then CREN
takes precedence.
To set up a Synchronous Master Reception:
1.
2.
3.
FIGURE 18-8:
TABLE 18-7:
DS39635B-page 242
INTCON
PIR3
PIE3
IPR3
RCSTA2
RCREG2 AUSART2 Receive Register
TXSTA2
SPBRG2
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.
Name
Note:
Initialize the SPBRG2 register for the appropriate
baud rate.
Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC.
Ensure bits CREN and SREN are clear.
RX2/DT2 pin
TX2/CK2 pin
(Interrupt)
RC2IF bit
bit SREN
SREN bit
CREN bit
RCREG2
Write to
Read
Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0.
AUSART SYNCHRONOUS
MASTER RECEPTION
AUSART2 Baud Rate Generator Register Low Byte
GIE/GIEH PEIE/GIEL
Q2
CSRC
SPEN
Bit 7
Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
‘0’
—
—
—
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
Bit 6
RX9
TX9
—
—
—
bit 0
TMR0IE
RC2IE
RC2IP
RC2IF
SREN
TXEN
Bit 5
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
bit 1
bit 2
INT0IE
TX2IE
TX2IP
CREN
SYNC
TX2IF
Preliminary
Bit 4
bit 3
ADDEN
RBIE
Bit 3
4.
5.
6.
7.
8.
9.
10. If any error occurred, clear the error by clearing
11. If using interrupts, ensure that the GIE and PEIE
—
—
—
—
If interrupts are desired, set enable bit RC2IE.
If 9-bit reception is desired, set bit RX9.
If a single reception is required, set bit SREN.
For continuous reception, set bit CREN.
Interrupt flag bit, RC2IF, will be set when
reception is complete and an interrupt will be
generated if the enable bit RC2IE was set.
Read the RCSTA2 register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG2 register.
bit CREN.
bits in the INTCON register (INTCON<7:6>) are
set.
bit 4
TMR0IF
BRGH
FERR
Bit 2
—
—
—
bit 5
INT0IF
OERR
TRMT
bit 6
Bit 1
© 2007 Microchip Technology Inc.
—
—
—
CCP3IE
CCP3IP
CCP3IF
bit 7
RX9D
TX9D
RBIF
Bit 0
Q1 Q2 Q3 Q4
on Page
Values
Reset
‘0’
57
59
59
59
60
60
60
60