PIC16F877-20/L Microchip Technology, PIC16F877-20/L Datasheet - Page 133

• Manufacturer Part Number: PIC16F877-20/L
• Description: IC MCU FLASH 8KX14 EE 44PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F877-20/L

• Program Memory Type: FLASH
• Program Memory Size: 14KB (8K x 14)
• Package / Case: 44-PLCC
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 33
• Eeprom Size: 256 x 8
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: MSSP/PSP/USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163022, DV164120
• Minimum Operating Temperature: 0 C
• On-chip Adc: 8-ch x 10-bit
• Data Rom Size: 256 B
• Height: 3.87 mm
• Length: 16.59 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4 V
• Width: 16.59 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164309 - MODULE SKT FOR PM3 44PLCC444-1001 - DEMO BOARD FOR PICMICRO MCUDVA16XL441 - ADAPTER DEVICE ICE 44PLCC309-1040 - ADAPTER 44-PLCC ZIF TO 40-DIP309-1039 - ADAPTER 44-PLCC TO 40-DIPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

12.12 Watchdog Timer (WDT)
The Watchdog Timer is a free running on-chip RC oscil-
lator which does not require any external components.
This RC oscillator is separate from the RC oscillator of
the OSC1/CLKIN pin. That means that the WDT will
run, even if the clock on the OSC1/CLKIN and OSC2/
CLKOUT pins of the device has been stopped, for
example, by execution of a SLEEP instruction.
During normal operation, a WDT time-out generates a
device RESET (Watchdog Timer Reset). If the device is
in SLEEP mode, a WDT time-out causes the device to
wake-up and continue with normal operation (Watch-
dog Timer Wake-up). The TO bit in the STATUS regis-
ter will be cleared upon a Watchdog Timer time-out.
The WDT can be permanently disabled by clearing
configuration bit WDTE (Section 12.1).
FIGURE 12-10:
TABLE 12-7:
2007h
81h,181h
Legend: Shaded cells are not used by the Watchdog Timer.
Note 1: See Register 12-1 for operation of these bits.
Address
2001 Microchip Technology Inc.
Note:
Config. bits
PSA and PS2:PS0 are bits in the OPTION_REG register.
OPTION_REG
Name
SUMMARY OF WATCHDOG TIMER REGISTERS
WATCHDOG TIMER BLOCK DIAGRAM
WDT Timer
Enable Bit
WDT
RBPU
From TMR0 Clock Source
(Figure 5-1)
Bit 7
(1)
BODEN
INTEDG
Bit 6
0
1
(1)
PSA
M
U
X
T0CS
Bit 5
CP1
WDT time-out period values may be found in the Elec-
trical Specifications section under parameter #31. Val-
ues for the WDT prescaler (actually a postscaler, but
shared with the Timer0 prescaler) may be assigned
using the OPTION_REG register.
T0SE
Bit 4
CP0
0
Note 1: The CLRWDT and SLEEP instructions
Time-out
8 - to - 1 MUX
MUX
WDT
Postscaler
2: When a CLRWDT instruction is executed
PWRTE
1
clear the WDT and the postscaler, if
assigned to the WDT, and prevent it from
timing out and generating a device
RESET condition.
Bit 3
and the prescaler is assigned to the WDT,
the prescaler count will be cleared, but
the prescaler assignment is not changed.
PSA
8
(1)
PSA
To TMR0 ( Figure 5-1 )
WDTE
Bit 2
PS2
PIC16F87X
PS2:PS0
FOSC1
Bit 1
DS30292C-page 131
PS1
FOSC0
Bit 0
PS0