PIC16F877-20/L Microchip Technology, PIC16F877-20/L Datasheet - Page 135

• Manufacturer Part Number: PIC16F877-20/L
• Description: IC MCU FLASH 8KX14 EE 44PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F877-20/L

• Program Memory Type: FLASH
• Program Memory Size: 14KB (8K x 14)
• Package / Case: 44-PLCC
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 33
• Eeprom Size: 256 x 8
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: MSSP/PSP/USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163022, DV164120
• Minimum Operating Temperature: 0 C
• On-chip Adc: 8-ch x 10-bit
• Data Rom Size: 256 B
• Height: 3.87 mm
• Length: 16.59 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4 V
• Width: 16.59 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164309 - MODULE SKT FOR PM3 44PLCC444-1001 - DEMO BOARD FOR PICMICRO MCUDVA16XL441 - ADAPTER DEVICE ICE 44PLCC309-1040 - ADAPTER 44-PLCC ZIF TO 40-DIP309-1039 - ADAPTER 44-PLCC TO 40-DIPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

FIGURE 12-11:
12.14 In-Circuit Debugger
When the DEBUG bit in the configuration word is pro-
grammed to a ’0’, the In-Circuit Debugger functionality
is enabled. This function allows simple debugging func-
tions when used with MPLAB
controller has this feature enabled, some of the
resources are not available for general use. Table 12-8
shows which features are consumed by the back-
ground debugger.
TABLE 12-8:
To use the In-Circuit Debugger function of the micro-
controller, the design must implement In-Circuit Serial
Programming connections to MCLR/V
RB7 and RB6. This will interface to the In-Circuit
Debugger module available from Microchip, or one of
the third party development tool companies.
I/O pins
Stack
Program Memory
Data Memory
Note 1: XT, HS or LP oscillator mode assumed.
OSC1
CLKOUT
INT pin
INTF Flag
(INTCON<1>)
GIE bit
(INTCON<7>)
INSTRUCTION FLOW
Instruction
Fetched
Instruction
Executed
2001 Microchip Technology Inc.
2: T
3: GIE = ’1’ assumed. In this case, after wake- up, the processor jumps to the interrupt routine.
4: CLKOUT is not available in these osc modes, but shown here for timing reference.
(4)
PC
If GIE = ’0’, execution will continue in-line.
OST
Inst(PC) = SLEEP
= 1024T
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1
Inst(PC - 1)
DEBUGGER RESOURCES
PC
OSC
WAKE-UP FROM SLEEP THROUGH INTERRUPT
0x070 (0x0F0, 0x170, 0x1F0)
(drawing not to scale) This delay will not be there for RC osc mode.
Address 0000h must be NOP
®
Last 100h words
Inst(PC + 1)
SLEEP
0x1EB - 0x1EF
PC+1
ICD. When the micro-
RB6, RB7
1 level
PP
, V
Processor in
SLEEP
DD
, GND,
PC+2
T
OST
(2)
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Inst(PC + 2)
Inst(PC + 1)
12.15 Program Verification/Code
If the code protection bit(s) have not been pro-
grammed, the on-chip program memory can be read
out for verification purposes.
12.16 ID Locations
Four memory locations (2000h - 2003h) are designated
as ID locations, where the user can store checksum or
other code identification numbers. These locations are
not accessible during normal execution, but are read-
able and writable during program/verify. It is recom-
mended that only the 4 Least Significant bits of the ID
location are used.
PC+2
Protection
Interrupt Latency
Dummy cycle
PC + 2
(2)
PIC16F87X
Inst(0004h)
Dummy cycle
0004h
DS30292C-page 133
Inst(0005h)
Inst(0004h)
0005h