PIC18F6621-I/PT Microchip Technology, PIC18F6621-I/PT Datasheet - Page 24

• Manufacturer Part Number: PIC18F6621-I/PT
• Description: IC PIC MCU FLASH 32KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F6621-I/PT

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.75K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 53
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3.75KB
• Cpu Speed: 40MHz
• No. Of Timers: 5
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3840 B
• Interface Type: MSSP, SPI, I2C, EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT64PT5 - SOCKET TRAN ICE 64MQFP/TQFPAC164319 - MODULE SKT MPLAB PM3 64TQFPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Lead Free Status / Rohs Status: Details

PIC18F6X2X/8X2X
4.3
A configuration address may be read and output on
PGD via the 4-bit command, ‘1001’. Configuration data
is read and written in a byte-wise fashion, so it is not
necessary to merge two bytes into a word prior to a
compare.
pared to the appropriate configuration data in the pro-
grammer’s
Section 4.1 for implementation details of reading
configuration data.
4.4
Data EEPROM is accessed one byte at a time via an
address pointer (register pair EEADR:EEADRH) and a
data latch (EEDATA). Data EEPROM is read by loading
EEADR:EEADRH with the desired memory location
and initiating a memory read by appropriately configur-
ing the EECON1 register. The data will be loaded into
EEDATA, where it may be serially output on PGD via
the 4-bit command, ‘0010’ (Shift Out Data Holding reg-
ister). A delay of P6 must be introduced after the falling
edge of the 8th PGC of the operand to allow PGD to
transition from an input to an output. During this time,
PGC must be held low (see Figure 4-4).
The command sequence to read a single byte of data
is shown in Table 4-2.
TABLE 4-2:
DS30499B-page 24
Step 1: Direct access to data EEPROM.
Step 2: Set the data EEPROM address pointer.
Step 3: Initiate a memory read.
Step 4: Load data into the Serial Data Holding register.
Note 1:
Command
0000
0000
0000
0000
0000
0000
0000
0000
0000
0010
4-bit
Verify Configuration Bits
Read Data EEPROM Memory
The <LSB> is undefined. The <MSB> is the data.
The result may then be immediately com-
memory
9E A6
9C A6
0E <Addr>
6E A9
OE <AddrH>
6E AA
80 A6
50 A8
6E F5
<LSB><MSB>
READ DATA EEPROM MEMORY
Data Payload
for
verification.
BCF
BCF
MOVLW
MOVWF
MOVLW
MOVWF
BSF
MOVF
MOVWF
Shift Out Data
Refer
EECON1, EEPGD
EECON1, CFGS
<Addr>
EEADR
<AddrH>
EEADRH
EECON1, RD
EEDATA, W, 0
TABLAT
to
(1)
FIGURE 4-3:
Core Instruction
No
Move to TABLAT
READ DATA EEPROM
FLOW
Shift Out Data
 2003 Microchip Technology Inc.
Address
Read
Done
Byte
Start
Done
Set
?
Yes