ST10F269Z2Q3 STMicroelectronics, ST10F269Z2Q3 Datasheet - Page 75

• Manufacturer Part Number: ST10F269Z2Q3
• Description: IC FLASH MEM 256KBIT 144-PQFP
• Manufacturer: STMicroelectronics
• Series: ST10r

Specifications of ST10F269Z2Q3

• Core Processor: ST10
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: CAN, EBI/EMI, SSC, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 111
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-QFP
• Processor Series: ST10F26x
• Core: ST10
• Data Bus Width: 16 bit
• Data Ram Size: 12 KB
• Interface Type: CAN, SSC, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 111
• Number Of Timers: 2 x 16 bit
• Operating Supply Voltage: 0.3 V to 4 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit x 10 bit
• Cpu Family: ST10
• Device Core Size: 16b
• Frequency (max): 40MHz
• Total Internal Ram Size: 12KB
• # I/os (max): 111
• Number Of Timers - General Purpose: 5
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• Instruction Set Architecture: CISC/RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: PQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-2042

ST10F269
Pin P3.12 (BHE/WRH) is another pin with an
alternate output function, however, its structure is
slightly different.
After reset the BHE or WRH function must be
used
configuration. In either of these cases, there is no
Figure 29 : Block Diagram of Pins P3.15 (CLKOUT) and P3.12 (BHE/WRH)
Note: Enabling the BHE or WRH function automatically enables the P3.12 output driver. Setting bit
DP3.12=’1’ is not required.
During bus hold pin P3.12 is switched back to its standard function and is then controlled by
DP3.12 and P3.12. Keep DP3.12 = ’0’ in this case to ensure floating in hold mode.
depending
Read DP3.x
Write DP3.x
Port Output
Read P3.x
Write P3.x
Direction
Latch
Latch
on
the
MUX
system
Alternate
Data
Output
1
0
Alternate
Function
Enable
“1”
start-up
1
0
1
0
MUX
MUX
possibility to program any port latches before.
Thus, the appropriate alternate function is
selected automatically. If BHE/WRH is not used in
the system, this pin can be used for general
purpose I/O by disabling the alternate function
(BYTDIS = ‘1’ / WRCFG=’0’).
Clock
Latch
Input
Output
Buffer
12 - PARALLEL PORTS
x = 15, 12
P3.12/BHE
P3.15/CLKOUT
75/184