C8051F310-GQ Silicon Laboratories Inc, C8051F310-GQ Datasheet - Page 150

• Manufacturer Part Number: C8051F310-GQ
• Description: IC 8051 MCU 16K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F31xr

Specifications of C8051F310-GQ

• Core Size: 8-Bit
• Program Memory Size: 16KB (16K x 8)
• Oscillator Type: Internal
• Core Processor: 8051
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 29
• Program Memory Type: FLASH
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 21x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• No. Of I/o's: 29
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 5
• Digital Ic Case: RoHS Compliant
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1445 - ADAPTER PROGRAM TOOLSTICK F310336-1329 - KIT REF DESIGN SENSORLESS BLDC336-1253 - DEV KIT FOR C8051F310/F311
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 336-1252

C8051F310/1/2/3/4/5
14.5.4. Slave Transmitter Mode
Serial data is transmitted on SDA and the clock is received on SCL. When slave events are enabled (INH
= 0), the interface enters Slave Receiver Mode (to receive the slave address) when a START followed by a
slave address and direction bit (READ in this case) is received. Upon entering Slave Transmitter Mode, an
interrupt is generated and the ACKRQ bit is set. Software responds to the received slave address with an
ACK, or ignores the received slave address with a NACK. If the received slave address is ignored, slave
interrupts will be inhibited until a START is detected. If the received slave address is acknowledged, data
should be written to SMB0DAT to be transmitted. The interface enters Slave Transmitter Mode, and trans-
mits one or more bytes of data. After each byte is transmitted, the master sends an acknowledge bit; if the
acknowledge bit is an ACK, SMB0DAT should be written with the next data byte. If the acknowledge bit is
a NACK, SMB0DAT should not be written to before SI is cleared (Note: an error condition may be gener-
ated if SMB0DAT is written following a received NACK while in Slave Transmitter Mode). The interface
exits Slave Transmitter Mode after receiving a STOP. Note that the interface will switch to Slave Receiver
Mode if SMB0DAT is not written following a Slave Transmitter interrupt. Figure 14.8 shows a typical Slave
Transmitter sequence. Two transmitted data bytes are shown, though any number of bytes may be trans-
mitted. Notice that the ‘data byte transferred’ interrupts occur after the ACK cycle in this mode.
150
S
Received by SMBus
Interface
Transmitted by
SMBus Interface
SLA
Figure 14.8. Typical Slave Transmitter Sequence
Interrupt
R
A
Data Byte
Rev. 1.5
Interrupt
A
S = START
P = STOP
N = NACK
R = READ
SLA = Slave Address
Data Byte
Interrupt
N
Interrupt
P