C8051F310-GQ Silicon Laboratories Inc, C8051F310-GQ Datasheet - Page 153

• Manufacturer Part Number: C8051F310-GQ
• Description: IC 8051 MCU 16K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F31xr

Specifications of C8051F310-GQ

• Core Size: 8-Bit
• Program Memory Size: 16KB (16K x 8)
• Oscillator Type: Internal
• Core Processor: 8051
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 29
• Program Memory Type: FLASH
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 21x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• No. Of I/o's: 29
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 5
• Digital Ic Case: RoHS Compliant
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1445 - ADAPTER PROGRAM TOOLSTICK F310336-1329 - KIT REF DESIGN SENSORLESS BLDC336-1253 - DEV KIT FOR C8051F310/F311
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 336-1252

15. UART0
UART0 is an asynchronous, full duplex serial port offering modes 1 and 3 of the standard 8051 UART.
Enhanced baud rate support allows a wide range of clock sources to generate standard baud rates (details
in
UART0 to start reception of a second incoming data byte before software has finished reading the previous
data byte.
UART0 has two associated SFRs: Serial Control Register 0 (SCON0) and Serial Data Buffer 0 (SBUF0).
The single SBUF0 location provides access to both transmit and receive registers. Writes to SBUF0
always access the Transmit register. Reads of SBUF0 always access the buffered Receive register;
it is not possible to read data from the Transmit register.
With UART0 interrupts enabled, an interrupt is generated each time a transmit is completed (TI0 is set in
SCON0), or a data byte has been received (RI0 is set in SCON0). The UART0 interrupt flags are not
cleared by hardware when the CPU vectors to the interrupt service routine. They must be cleared manually
by software, allowing software to determine the cause of the UART0 interrupt (transmit complete or receive
complete).
Section “15.1. Enhanced Baud Rate Generation” on page
Rate Generator
UART Baud
Write to
SBUF
Figure 15.1. UART0 Block Diagram
Tx Clock
Rx Clock
Stop Bit
Start
Start
SBUF
Read
SCON
D
TB8
SET
CLR
Shift
Input Shift Register
Q
Shift
SFR Bus
(RX Latch)
(9 bits)
Tx Control
Rx Control
SBUF
0x1FF
SFR Bus
Zero Detector
(TX Shift)
SBUF
Rev. 1.5
RB8
Load SBUF
Tx IRQ
Rx IRQ
RI
TI
SBUF
Load
Send
Data
C8051F310/1/2/3/4/5
Interrupt
Serial
Port
154). Received data buffering allows
TX
RX
Crossbar
Crossbar
Port I/O
153