PIC18F4331-I/P Microchip Technology, PIC18F4331-I/P Datasheet - Page 208

• Manufacturer Part Number: PIC18F4331-I/P
• Description: IC PIC MCU FLASH 4KX16 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4331-I/P

• Core Size: 8-Bit
• Program Memory Size: 8KB (4K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, Power Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: EUSART, I2C, SPI, SSP
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 9 bit
• Package: 40PDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3-DB18F4431 - BOARD DAUGHTER ICEPIC3DVA18XP400 - DEVICE ADAPTER 18F4220 PDIP 40LD444-1001 - DEMO BOARD FOR PICMICRO MCUACICE0206 - ADAPTER MPLABICE 40P 600 MIL
• Lead Free Status / Rohs Status: Details

PIC18F2331/2431/4331/4431
17.11 PWM Output and Polarity Control
There are three device Configuration bits associated
with the PWM module that provide PWM output pin
control defined in the CONFIG3L Configuration
register. They are:
• HPOL
• LPOL
• PWMPIN
These three Configuration bits work in conjunction with
the three PWM Enable bits (PWMEN2:PWMEN0) in
the PWMCON0 register. The Configuration bits and
PWM enable bits ensure that the PWM pins are in the
correct states after a device Reset occurs.
17.11.1
The PWMEN2:PWMEN0 control bits enable each
PWM output pin as required in the application.
All PWM I/O pins are general purpose I/O. When a pair
of pins are enabled for PWM output, the PORT and
TRIS registers controlling the pins are disabled. Refer
to Figure 17-23 for details.
FIGURE 17-23:
DS39616C-page 206
OUTPUT PIN CONTROL
Note:
PWM Signal from Module
PWM Pin Enable
Data Bus
WR PORT
WR TRIS
RD TRIS
RD PORT
PWM I/O PIN BLOCK DIAGRAM
I/O pin has protection diodes to V
Data Latch
TRIS Latch
D
D
CK
CK
Q
Q
Q
Q
Preliminary
DD
and V
1
0
SS
. PWM polarity selection logic not shown for clarity.
17.11.2
The polarity of the PWM I/O pins is set during device
programming via the HPOL and LPOL Configuration
bits in the CONFIG3L Configuration register. The
HPOL Configuration bit sets the output polarity for the
high side PWM outputs: PWM1, PWM3, PWM5 and
PWM7. The polarity is active-high when HPOL is
cleared (= 0), and active-low when it is set (= 1).
The LPOL Configuration bit sets the output polarity for
the low side PWM outputs: PWM0, PWM2, PWM4 and
PWM6. As with HPOL, they are active-high when LPOL
is cleared and active-low when it is set.
All output signals generated by the PWM module are
referenced to the polarity control bits, including those
generated by Fault inputs or manual override (see
Section 17.10 “PWM Output Override”).
The default polarity Configuration bits have the PWM
I/O pins in active-high output polarity.
Q
EN
D
OUTPUT POLARITY CONTROL
V
V
P
N
DD
SS
© 2007 Microchip Technology Inc.
TTL or
Schmitt
Trigger
I/O Pin