PIC18F4331-I/P Microchip Technology, PIC18F4331-I/P Datasheet - Page 40

• Manufacturer Part Number: PIC18F4331-I/P
• Description: IC PIC MCU FLASH 4KX16 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4331-I/P

• Core Size: 8-Bit
• Program Memory Size: 8KB (4K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, Power Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: EUSART, I2C, SPI, SSP
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 9 bit
• Package: 40PDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3-DB18F4431 - BOARD DAUGHTER ICEPIC3DVA18XP400 - DEVICE ADAPTER 18F4220 PDIP 40LD444-1001 - DEMO BOARD FOR PICMICRO MCUACICE0206 - ADAPTER MPLABICE 40P 600 MIL
• Lead Free Status / Rohs Status: Details

PIC18F2331/2431/4331/4431
3.3.2
In SEC_IDLE mode, the CPU is disabled, but the
peripherals continue to be clocked from the Timer1
oscillator. This mode is entered by setting the Idle bit,
modifying SCS1:SCS0 = 01 and executing a SLEEP
instruction. When the clock source is switched (see
Figure 3-5) to the Timer1 oscillator, the primary
oscillator is shut down, the OSTS bit is cleared and the
T1RUN bit is set.
FIGURE 3-5:
FIGURE 3-6:
DS39616C-page 38
Peripheral
Note:
Program
Counter
T1OSI
OSC1
Clock
Clock
Note 1: T
CPU
CPU Clock
PLL Clock
Peripheral
Program
Counter
Output
T1OSI
OSC1
Clock
SEC_IDLE MODE
The Timer1 oscillator should already be
running prior to entering SEC_IDLE mode.
If the T1OSCEN bit is not set when the
SLEEP instruction is executed, a forced
NOP will be executed instead and entry to
SEC_IDLE mode will not occur. If the
Timer1 oscillator is enabled, but not yet
running, peripheral clocks will be delayed
until the oscillator has started; in such sit-
uations, initial oscillator operation is far
from stable and unpredictable operation
may result.
Q1
Wake from Interrupt Event
Q2
OST
PC
Q3
= 1024 T
PC
Q4
TIMING TRANSITION FOR ENTRY TO SEC_IDLE MODE
TIMING TRANSITION FOR WAKE FROM SEC_RUN MODE (HSPLL)
Q1
OSC
Q1
1
T
; T
OST (1)
PLL
2
= 2 ms (approx). These intervals are not shown to scale.
Q2
PC + 2
3
T
PLL
OSTS bit Set
Clock Transition
Q3
(1)
4
Preliminary
5
Q4
PC + 2
6
Q1
1
2
7
When a wake event occurs, the peripherals continue to
be clocked from the Timer1 oscillator. After a 10 μs
delay following the wake event, the CPU begins execut-
ing code, being clocked by the Timer1 oscillator. The
microcontroller operates in SEC_RUN mode until the
primary clock becomes ready. When the primary clock
becomes ready, a clock switch back to the primary clock
occurs (see Figure 3-6). When the clock switch is com-
plete, the T1RUN bit is cleared, the OSTS bit is set and
the primary clock is providing the system clock. The
IDLEN and SCS bits are not affected by the wake-up;
the Timer1 oscillator continues to run.
Clock Transition
3
8
4
5
PC + 4
6
7
8
© 2007 Microchip Technology Inc.
Q2
Q3 Q4
Q1
PC + 6
Q2
Q3