C8051T606-GM Silicon Laboratories Inc, C8051T606-GM Datasheet - Page 131

• Manufacturer Part Number: C8051T606-GM
• Description: IC 8051 MCU 1.5K-EEPROM 11-QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051T60xr

Specifications of C8051T606-GM

• Program Memory Type: OTP
• Program Memory Size: 1.5KB (1.5K x 8)
• Package / Case: 11-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 6
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051T6x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: I2C, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 3
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051T606DK
• Minimum Operating Temperature: - 40 C
• Package: 11QFN EP
• Device Core: 8051
• Family Name: C8051T60x
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1668 - CARD DAUGHTER QFN10 SOCKET336-1667 - CARD DAUGHTER MSOP SOCKET336-1666 - KIT DEVELOPMENT FOR C8051T606336-1404 - KIT DEV FOR C8051T60X MCU'S
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1662-5

23.5. SMBus Transfer Modes
The SMBus interface may be configured to operate as master and/or slave. At any particular time, it will be
operating in one of the following four modes: Master Transmitter, Master Receiver, Slave Transmitter, or
Slave Receiver. The SMBus interface enters Master Mode any time a START is generated, and remains in
Master Mode until it loses an arbitration or generates a STOP. An SMBus interrupt is generated at the end
of all SMBus byte frames. As a receiver, the interrupt for an ACK occurs before the ACK. As a transmitter,
interrupts occur after the ACK.
23.5.1. Write Sequence (Master)
During a write sequence, an SMBus master writes data to a slave device. The master in this transfer will be
a transmitter during the address byte, and a transmitter during all data bytes. The SMBus interface gener-
ates the START condition and transmits the first byte containing the address of the target slave and the
data direction bit. In this case the data direction bit (R/W) will be logic 0 (WRITE). The master then trans-
mits one or more bytes of serial data. After each byte is transmitted, an acknowledge bit is generated by
the slave. The transfer is ended when the STO bit is set and a STOP is generated. Note that the interface
will switch to Master Receiver Mode if SMB0DAT is not written following a Master Transmitter interrupt.
Figure 23.5 shows a typical master write sequence. Two transmit data bytes are shown, though any num-
ber of bytes may be transmitted. Notice that all of the “data byte transferred” interrupts occur after the ACK
cycle in this mode.
S
Received by SMBus
Interface
Transmitted by
SMBus Interface
SLA
Figure 23.5. Typical Master Write Sequence
W
A
Interrupt Locations
Data Byte
Rev. 1.2
C8051T600/1/2/3/4/5/6
A
S = START
P = STOP
A = ACK
W = WRITE
SLA = Slave Address
Data Byte
A
P
131