ATTINY2313A-SUR Atmel, ATTINY2313A-SUR Datasheet - Page 122

• Manufacturer Part Number: ATTINY2313A-SUR
• Description: MCU AVR 2KB FLASH 20MHZ 20SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY2313A-SUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -

14.3.2
14.3.3
122
ATtiny2313A/4313
Double Speed Operation (U2X)
External Clock
Table 14-1.
Note:
Some examples of UBRR values for some system clock frequencies are found in
(see
The transfer rate can be doubled by setting the U2X bit in UCSRA. Setting this bit only has effect
for the asynchronous operation. Set this bit to zero when using synchronous operation.
Setting this bit will reduce the divisor of the baud rate divider from 16 to 8, effectively doubling
the transfer rate for asynchronous communication. Note however that the Receiver will in this
case only use half the number of samples (reduced from 16 to 8) for data sampling and clock
recovery, and therefore a more accurate baud rate setting and system clock are required when
this mode is used. For the Transmitter, there are no downsides.
External clocking is used by the synchronous slave modes of operation. The description in this
section refers to
External clock input from the XCK pin is sampled by a synchronization register to minimize the
chance of meta-stability. The output from the synchronization register must then pass through
an edge detector before it can be used by the Transmitter and Receiver. This process intro-
duces a two CPU clock period delay and therefore the maximum external XCK clock frequency
is limited by the following equation:
Note that f
add some margin to avoid possible loss of data due to frequency variations.
Operating Mode
Asynchronous Normal
mode (U2X = 0)
Asynchronous Double
Speed mode (U2X = 1)
Synchronous Master
mode
page
BAUD
f
UBRR
OSC
1. The baud rate is defined to be the transfer rate in bit per second (bps)
osc
141).
depends on the stability of the system clock source. It is therefore recommended to
Equations for Calculating Baud Rate Register Setting
Figure 14-2
Baud rate (in bits per second, bps)
System Oscillator clock frequency
Contents of the UBRRH and UBRRL Registers, (0-4095)
BAUD
BAUD
BAUD
Equation for Calculating
for details.
Baud Rate
=
=
=
-------------------------------------- -
16 UBRR
---------------------------------- -
8 UBRR
---------------------------------- -
2 UBRR
(
(
(
f
XCK
f
f
f
OSC
OSC
OSC
(1)
<
+
+
+
f
---------- -
1
1
OSC
1
4
)
)
)
Equation for Calculating
UBRR
UBRR
UBRR
UBRR Value
=
=
=
----------------------- - 1
16BAUD
------------------- - 1
8BAUD
------------------- - 1
2BAUD
f
f
f
OSC
OSC
OSC
–
–
–
8246A–AVR–11/09
Table 14-9