PIC16F72-I/SOG Microchip Technology, PIC16F72-I/SOG Datasheet - Page 72

• Manufacturer Part Number: PIC16F72-I/SOG
• Description: IC PIC MCU FLASH 2KX14 28-SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F72-I/SOG

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

PIC16F72
11.13 Watchdog Timer (WDT)
The Watchdog Timer is a free running, on-chip RC
oscillator that does not require any external compo-
nents. This RC oscillator is separate from the RC oscil-
lator of the OSC1/CLKI pin. That means that the WDT
will run, even if the clock on the OSC1/CLKI and OSC2/
CLKO pins of the device has been stopped, for
example, by execution of a SLEEP instruction.
During normal operation, a WDT time-out generates a
device RESET (Watchdog Timer Reset). If the device is
in SLEEP mode, a WDT time-out causes the device to
wake-up and continue with normal operation (Watchdog
Timer Wake-up). The TO bit in the STATUS register will
be cleared upon a Watchdog Timer time-out.
The WDT can be permanently disabled by clearing
configuration bit WDTEN (see Section 11.1).
FIGURE 11-11:
TABLE 11-7:
DS39597C-page 70
2007h
81h,181h
Legend: Shaded cells are not used by the Watchdog Timer.
Note 1: See Register 11-1 for operation of these bits.
Address
Note: PSA and PS2:PS0 are bits in the OPTION register.
Config. bits
OPTION
Name
SUMMARY OF WATCHDOG TIMER REGISTERS
WDT Timer
Enable Bit
WATCHDOG TIMER BLOCK DIAGRAM
WDT
From TMR0 Clock Source
(Figure 4-1)
RBPU
Bit 7
(1)
BOREN
INTEDG
Bit 6
0
1
PSA
(1)
M
U
X
T0CS
Bit 5
—
T0SE
0
Bit 4
WDT time-out period values may be found in the Elec-
trical Specifications section under parameter #31. Val-
ues for the WDT prescaler (actually a postscaler, but
shared with the Timer0 prescaler) may be assigned
using the OPTION register.
CP
Time-out
8 - to - 1 MUX
MUX
Note 1: The CLRWDT and SLEEP instructions
WDT
Postscaler
PWRTEN
2: When a CLRWDT instruction is executed
1
8
Bit 3
PSA
clear the WDT and the postscaler, if
assigned to the WDT, and prevent it from
timing out and generating a device
RESET condition.
and the prescaler is assigned to the WDT,
the prescaler count will be cleared, but
the prescaler assignment is not changed.
(1)
PSA
To TMR0 (Figure 4-1)
WDTEN
Bit 2
PS2
© 2007 Microchip Technology Inc.
PS2:PS0
FOSC1
Bit 1
PS1
FOSC0
Bit 0
PS0