ATTINY25V-15ST Atmel, ATTINY25V-15ST Datasheet - Page 34

• Manufacturer Part Number: ATTINY25V-15ST
• Description: MCU AVR 2K FLASH 4MHZ 8-SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY25V-15ST

• Package / Case: 8-SOIC (3.9mm Width)
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Speed: 8MHz
• Number Of I /o: 6
• Eeprom Size: 128 x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Program Memory Size: 2KB (2K x 8)
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: USI
• Core Size: 8-Bit
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

7.7
7.7.1
7.7.2
7.7.3
7.7.4
34
Minimizing Power Consumption
ATtiny25/45/85
Analog to Digital Converter
Analog Comparator
Brown-out Detector
Internal Voltage Reference
• Bit 2- PRTIM0: Power Reduction Timer/Counter0
Writing a logic one to this bit shuts down the Timer/Counter0 module. When the Timer/Counter0
is enabled, operation will continue like before the shutdown.
• Bit 1 - PRUSI: Power Reduction USI
Writing a logic one to this bit shuts down the USI by stopping the clock to the module. When
waking up the USI again, the USI should be re initialized to ensure proper operation.
• Bit 0 - PRADC: Power Reduction ADC
Writing a logic one to this bit shuts down the ADC. The ADC must be disabled before shut down.
The analog comparator cannot use the ADC input MUX when the ADC is shut down.
There are several issues to consider when trying to minimize the power consumption in an AVR
controlled system. In general, sleep modes should be used as much as possible, and the sleep
mode should be selected so that as few as possible of the device’s functions are operating. All
functions not needed should be disabled. In particular, the following modules may need special
consideration when trying to achieve the lowest possible power consumption.
If enabled, the ADC will be enabled in all sleep modes. To save power, the ADC should be dis-
abled before entering any sleep mode. When the ADC is turned off and on again, the next
conversion will be an extended conversion. Refer to
for details on ADC operation.
When entering Idle mode, the Analog Comparator should be disabled if not used. When entering
ADC Noise Reduction mode, the Analog Comparator should be disabled. In the other sleep
modes, the Analog Comparator is automatically disabled. However, if the Analog Comparator is
set up to use the Internal Voltage Reference as input, the Analog Comparator should be dis-
abled in all sleep modes. Otherwise, the Internal Voltage Reference will be enabled,
independent of sleep mode. Refer to
configure the Analog Comparator.
If the Brown-out Detector is not needed in the application, this module should be turned off. If the
Brown-out Detector is enabled by the BODLEVEL Fuses, it will be enabled in all sleep modes,
and hence, always consume power. In the deeper sleep modes, this will contribute significantly
to the total current consumption. Refer to
configure the Brown-out Detector.
The Internal Voltage Reference will be enabled when needed by the Brown-out Detection, the
Analog Comparator or the ADC. If these modules are disabled as described in the sections
above, the internal voltage reference will be disabled and it will not be consuming power. When
turned on again, the user must allow the reference to start up before the output is used. If the
reference is kept on in sleep mode, the output can be used immediately. Refer to
age Reference” on page 40
for details on the start-up time.
“Analog Comparator” on page 108
“Brown-out Detection” on page 38
“Analog to Digital Converter” on page 111
for details on how to
for details on how to
7598H–AVR–07/09
“Internal Volt-