AT89C5130A-RDRUM Atmel, AT89C5130A-RDRUM Datasheet - Page 139

• Manufacturer Part Number: AT89C5130A-RDRUM
• Description: MCU 8051 16K FLASH USB 64-VQFP
• Manufacturer: Atmel
• Series: AT89C513xr

Specifications of AT89C5130A-RDRUM

• Core Processor: C52X2
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: LED, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: AT89x
• Core: 8051
• Data Bus Width: 8 bit
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: AT89STK-05
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -

21.11 USB Registers
4337K–USB–04/08
Table 21-3.
Reset Value = 00h
Bit Number
USBE
7
7
6
5
4
3
2
1
0
SUSPCLK
Bit Mnemonic
USBCON Register
USBCON (S:BCh)
USB Global Control Register
SDRMWUP
SUSPCLK
RMWUPE
DETACH
FADDEN
UPRSM
CONFG
6
USBE
SDRMWUP
5
Description
USB Enable
Set this bit to enable the USB controller.
Clear this bit to disable and reset the USB controller, to disable the USB
transceiver an to disable the USB controller clock inputs.
Suspend USB Clock
Set this bit to disable the 48 MHz clock input (Resume Detection is still active).
Clear this bit to enable the 48 MHz clock input.
Send Remote Wake Up
Set this bit to force an external interrupt on the USB controller for Remote Wake
UP purpose.
An upstream resume is send only if the bit RMWUPE is set, all USB clocks are
enabled AND the USB bus was in SUSPEND state for at least 5 ms. See UPRSM
below.
This bit is cleared by software.
Detach Command
Set this bit to simulate a Detach on the USB line. The V
state.
Clear this bit to maintain V
Upstream Resume (read only)
This bit is set by hardware when SDRMWUP has been set and if RMWUPE is
enabled.
This bit is cleared by hardware after the upstream resume has been sent.
Remote Wake-Up Enable
Set this bit to enabled request an upstream resume signaling to the host.
Clear this bit otherwise.
Note: Do not set this bit if the host has not set the DEVICE_REMOTE_WAKEUP
feature for the device.
Configured
This bit will be set by the device firmware after a SET_CONFIGURATION request
with a non-zero value has been correctly processed.
It will be cleared by the device firmware when a SET_CONFIGURATION request
with a zero value is received. It is cleared by hardware on hardware reset or when
an USB reset is detected on the bus (SE0 state for at least 32 Full Speed bit times:
typically 2.7 µs).
Function Address Enable
This bit will be set by the device firmware after a successful status phase of a
SET_ADDRESS transaction.
It will not be cleared afterwards by the device firmware. It is cleared by hardware
on hardware reset or when an USB reset is received (see above). When this bit is
cleared, the default function address is used (0).
DETACH
4
REF
UPRSM
3
at high level.
AT89C5130A/31A-M
RMWUPE
2
REF
CONFG
pin is then in a floating
1
FADDEN
0
139