DSPIC33FJ128MC710-E/PT Microchip Technology, DSPIC33FJ128MC710-E/PT Datasheet - Page 21
![IC DSPIC MCU/DSP 128K 100TQFP](/photos/12/13/121330/c04-100-tqfp_sml.jpg)
DSPIC33FJ128MC710-E/PT
Manufacturer Part Number
DSPIC33FJ128MC710-E/PT
Description
IC DSPIC MCU/DSP 128K 100TQFP
Manufacturer
Microchip Technology
Series
dsPIC™ 33Fr
Datasheets
1.DSPIC33FJ12GP201-ISO.pdf
(90 pages)
2.DSPIC33FJ64MC506-IPT.pdf
(340 pages)
3.DSPIC33FJ64MC506-IPT.pdf
(30 pages)
Specifications of DSPIC33FJ128MC710-E/PT
Core Processor
dsPIC
Core Size
16-Bit
Speed
40 MIPs
Connectivity
CAN, I²C, IrDA, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
Number Of I /o
85
Program Memory Size
128KB (128K x 8)
Program Memory Type
FLASH
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 24x10b/12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
100-TFQFP
For Use With
AC164333 - MODULE SKT FOR PM3 100QFPMA330013 - MODULE PLUG-IN DSPIC33 100TQFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
- DSPIC33FJ12GP201-ISO PDF datasheet
- DSPIC33FJ64MC506-IPT PDF datasheet #2
- DSPIC33FJ64MC506-IPT PDF datasheet #3
- Current page: 21 of 340
- Download datasheet (5Mb)
2.0
2.1
Getting
dsPIC33FJXXXMCX06/X08/X10 family of 16-bit Digital
Signal Controllers (DSCs) requires attention to a
minimal set of device pin connections before
proceeding with development. The following is a list of
pin names, which must always be connected:
• All V
• All AV
• V
• MCLR pin
• PGECx/PGEDx pins used for In-Circuit Serial
• OSC1 and OSC2 pins when external oscillator
Additionally, the following pins may be required:
• V
© 2009 Microchip Technology Inc.
Note:
(see Section 2.2 “Decoupling Capacitors”)
is not used)
(see Section 2.2 “Decoupling Capacitors”)
(see Section 2.3 “Capacitor on Internal Voltage
Regulator (V
(see Section 2.4 “Master Clear (MCLR) Pin”)
Programming™ (ICSP™) and debugging purposes
(see Section 2.5 “ICSP Pins”)
source is used
(see Section 2.6 “External Oscillator Pins”)
reference for ADC module is implemented
Note:
REF
CAP
DD
+/V
/V
DD
GUIDELINES FOR GETTING
STARTED WITH 16-BIT
DIGITAL SIGNAL
CONTROLLERS
Basic Connection Requirements
DDCORE
and V
REF
and AV
This data sheet summarizes the features
of the dsPIC33FJXXXMCX06/X08/X10
family of devices. It is not intended to be a
comprehensive
complement the information in this data
sheet, refer to the “dsPIC33F Family
Reference Manual”, which is available
from
(www.microchip.com).
The AV
connected independent of the ADC
voltage reference source.
- pins used when external voltage
CAP
SS
started
SS
pins
/V
DD
DDCORE
pins (regardless if ADC module
the
and AV
reference
)”)
Microchip
SS
with
dsPIC33FJXXXMCX06/X08/X10
pins must be
source.
website
To
the
2.2
The use of decoupling capacitors on every pair of
power supply pins, such as V
AV
Consider the following criteria when using decoupling
capacitors:
• Value and type of capacitor: Recommendation
• Placement on the printed circuit board: The
• Handling high frequency noise: If the board is
• Maximizing performance: On the board layout
of 0.1 µF (100 nF), 10-20V. This capacitor should
be a low-ESR and have resonance frequency in
the range of 20 MHz and higher. It is
recommended that ceramic capacitors be used.
decoupling capacitors should be placed as close
to the pins as possible. It is recommended to
place the capacitors on the same side of the
board as the device. If space is constricted, the
capacitor can be placed on another layer on the
PCB using a via; however, ensure that the trace
length from the pin to the capacitor is within
one-quarter inch (6 mm) in length.
experiencing high frequency noise, upward of
tens of MHz, add a second ceramic-type capacitor
in parallel to the above described decoupling
capacitor. The value of the second capacitor can
be in the range of 0.01 µF to 0.001 µF. Place this
second capacitor next to the primary decoupling
capacitor. In high-speed circuit designs, consider
implementing a decade pair of capacitances as
close to the power and ground pins as possible.
For example, 0.1 µF in parallel with 0.001 µF.
from the power supply circuit, run the power and
return traces to the decoupling capacitors first,
and then to the device pins. This ensures that the
decoupling capacitors are first in the power chain.
Equally important is to keep the trace length
between the capacitor and the power pins to a
minimum thereby reducing PCB track inductance.
SS
is required.
Decoupling Capacitors
DD
, V
DS70287C-page 19
SS
, AV
DD
and
Related parts for DSPIC33FJ128MC710-E/PT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![TC1014-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1014-5.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.8VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-4.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1186-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1186-2.85VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet: