AT32UC3B0512-Z2UR Atmel, AT32UC3B0512-Z2UR Datasheet - Page 381
AT32UC3B0512-Z2UR
Manufacturer Part Number
AT32UC3B0512-Z2UR
Description
IC MCU AVR32 512K FLASH 64QFN
Manufacturer
Atmel
Series
AVR®32 UC3r
Datasheet
1.AT32UC3B164-AUR.pdf
(680 pages)
Specifications of AT32UC3B0512-Z2UR
Package / Case
64-QFN
Voltage - Supply (vcc/vdd)
1.65 V ~ 1.95 V
Operating Temperature
-40°C ~ 85°C
Speed
60MHz
Number Of I /o
44
Core Processor
AVR
Program Memory Type
FLASH
Ram Size
96K x 8
Program Memory Size
512KB (512K x 8)
Data Converters
A/D 8x10b
Oscillator Type
Internal
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Connectivity
I²C, IrDA, SPI, SSC, UART/USART, USB
Core Size
32-Bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT32UC3B0512-Z2UR
Manufacturer:
ATMEL
Quantity:
2 010
- Current page: 381 of 680
- Download datasheet (10Mb)
22.7.2
22.7.2.1
22.7.2.2
22.7.2.3
32059J–12/2010
USB Device Operation
Introduction
Power-On and reset
USB reset
In device mode, the USBB supports full- and low-speed data transfers.
In addition to the default control endpoint, six endpoints are provided, which can be configured
with the types isochronous, bulk or interrupt, as described in
The device mode starts in the Idle state, so the pad consumption is reduced to the minimum.
Figure 22-13 on page 381
Figure 22-13. Device Mode States
After a hardware reset, the USBB device mode is in the Reset state. In this state:
• The macro clock is stopped in order to minimize power consumption (FRZCLK is written to
• The internal registers of the device mode are reset.
• The endpoint banks are de-allocated.
• Neither D+ nor D- is pulled up (DETACH is written to one).
D+ or D- will be pulled up according to the selected speed as soon as the DETACH bit is written
to zero and VBus is present. See
When the USBB is enabled (USBE is written to one) in device mode (ID is one), its device mode
state goes to the Idle state with minimal power consumption. This does not require the USB
clock to be activated.
The USBB device mode can be disabled and reset at any time by disabling the USBB (by writing
a zero to USBE) or when host mode is engaged (ID is zero).
The USB bus reset is managed by hardware. It is initiated by a connected host.
When a USB reset is detected on the USB line, the following operations are performed by the
controller:
one).
describes the USBB device mode main states.
RESET
HW
| ID = 0
USBE = 0
“Device mode”
Reset
| ID = 0
& ID = 1
USBE = 0
state>
other
<any
USBE = 1
for further details.
Idle
Table 22-1 on page
AT32UC3B
365.
381
Related parts for AT32UC3B0512-Z2UR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: