ATSAM3U1CA-CU Atmel, ATSAM3U1CA-CU Datasheet - Page 948

• Manufacturer Part Number: ATSAM3U1CA-CU
• Description: IC MCU 32BIT 64KB FLASH 100TFBGA
• Manufacturer: Atmel
• Series: SAM3Ur

Specifications of ATSAM3U1CA-CU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 96MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 57
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 4x10b, 4x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 20 KB
• Interface Type: 3xUSART, TWI, 4xSPI, Bus
• Maximum Clock Frequency: 96 MHz
• Number Of Programmable I/os: 57
• Number Of Timers: 8
• Operating Supply Voltage: 1.62 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3U-EK
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

39.6.4
39.6.5
948
948
SAM3U Series
SAM3U Series
USB V2.0 High Speed BUS Transactions
Endpoint Configuration
Each transfer results in one or more transactions over the USB bus.
There are five kinds of transactions flowing across the bus in packets:
Figure 39-3. Control Read and Write Sequences
A status IN or OUT transaction is identical to a data IN or OUT transaction.
The endpoint 0 is always a control endpoint, it must be programmed and active in order to be
enabled when the End Of Reset interrupt occurs.
To configure the endpoints:
Note: For control endpoints the direction has no effect.
Control endpoints can generate interrupts and use only 1 bank.
1. Setup Transaction
2. Data IN Transaction
3. Data OUT Transaction
4. Status IN Transaction
5. Status OUT Transaction
• Fill the configuration register (UDPHS_EPTCFG) with the endpoint size, direction (IN or
• Fill the number of transactions (NB_TRANS) for isochronous endpoints.
• Verify that the EPT_MAPD flag is set. This flag is set if the endpoint size and the number of
• Configure control flags of the endpoint and enable it in UDPHS_EPTCTLENBx according to
OUT), type (CTRL, Bulk, IT, ISO) and the number of banks.
banks are correct compared to the FIFO maximum capacity and the maximum number of
allowed banks.
“UDPHS Endpoint Control Register” on page
Control Write
Control Read
No Data
Control
Setup Stage
Setup Stage
Setup Stage
Setup TX
Setup TX
Setup TX
Status Stage
Status IN TX
Data OUT TX
Data IN TX
Data Stage
Data Stage
993.
Data OUT TX
Data IN TX
6430D–ATARM–25-Mar-11
6430D–ATARM–25-Mar-11
Status OUT TX
Status Stage
Status Stage
Status IN TX