MC9S08GT8ACFBE Freescale Semiconductor, MC9S08GT8ACFBE Datasheet - Page 38

• Manufacturer Part Number: MC9S08GT8ACFBE
• Description: IC MCU 8K FLASH 1K RAM 44-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08GT8ACFBE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFP
• Processor Series: S08GT
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C/SCI/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Operating Supply Voltage: 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: M68EVB908GB60E, M68DEMO908GB60E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• For Use With: M68DEMO908GB60E - BOARD DEMO MC9S08GB60M68EVB908GB60E - BOARD EVAL FOR MC9S08GB60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Modes of Operation
3.5.6
When the MCU enters any stop mode, system clocks to the internal peripheral modules are stopped. Even
in the exception case (ENBDM = 1), where clocks to the background debug logic continue to operate,
clocks to the peripheral systems are halted to reduce power consumption. Refer to
Mode,”
behavior in stop modes.
I/O Pins
Memory
ICG — In stop3 mode, the ICG enters its low-power standby state. Either the oscillator or the internal
reference may be kept running when the ICG is in standby by setting the appropriate control bit. In both
stop2 and stop1 modes, the ICG is turned off. Neither the oscillator nor the internal reference can be kept
running in stop2 or stop1, even if enabled within the ICG module.
TPM — When the MCU enters stop mode, the clock to the TPM1 and TPM2 modules stop. The modules
halt operation. If the MCU is configured to go into stop2 or stop1 mode, the TPM modules will be reset
upon wake-up from stop and must be reinitialized.
ATD — When the MCU enters stop mode, the ATD will enter a low-power standby state
operation will occur while in stop. If the MCU is configured to go into stop2 or stop1 mode, the ATD will
be reset upon wake-up from stop and must be reinitialized.
KBI — During stop3, the KBI pins that are enabled continue to function as interrupt sources that are
capable of waking the MCU from stop3. The KBI is disabled in stop1 and stop2 and must be reinitialized
after waking up from either of these modes.
SCI — When the MCU enters stop mode, the clocks to the SCI1 and SCI2 modules stop. The modules
halt operation. If the MCU is configured to go into stop2 or stop1 mode, the SCI modules will be reset
upon wake-up from stop and must be reinitialized.
SPI — When the MCU enters stop mode, the clocks to the SPI module stop. The module halts operation.
If the MCU is configured to go into stop2 or stop1 mode, the SPI module will be reset upon wake-up from
stop and must be reinitialized.
38
•
•
•
•
•
•
All I/O pin states remain unchanged when the MCU enters stop3 mode.
If the MCU is configured to go into stop2 mode, all I/O pins states are latched before entering stop.
If the MCU is configured to go into stop1 mode, all I/O pins are forced to their default reset state
upon entry into stop.
All RAM and register contents are preserved while the MCU is in stop3 mode.
All registers will be reset upon wake-up from stop2, but the contents of RAM are preserved and
pin states remain latched until the PPDACK bit is written. The user may save any memory-mapped
register data into RAM before entering stop2 and restore the data upon exit from stop2.
All registers will be reset upon wake-up from stop1 and the contents of RAM are not preserved.
The MCU must be initialized as upon reset. The contents of the FLASH memory are nonvolatile
and are preserved in any of the stop modes.
Section 3.5.2, “Stop2
On-Chip Peripheral Modules in Stop Modes
Mode,” and
MC9S08GT16A/GT8A Data Sheet, Rev. 1
Section 3.5.3, “Stop3
Mode,” for specific information on system
Section 3.5.1, “Stop1
Freescale Semiconductor
.
No conversion